參數資料
型號： KSZ8842-16MQL-EVAL
廠商： Micrel Inc
文件頁數： 82/141頁
文件大小： 0K
描述： BOARD EVALUATION KSZ8842-16MQL
標準包裝： 1
主要目的： 接口，以太網控制器（PHY 和 MAC）
嵌入式： 否
已用 IC / 零件： KSZ8842-16MQL
主要屬性： 2 個端口，100BASE-TX/10BASE-T，管理型
次要屬性： 8/16 位接口，LinkMD 線纜診斷
已供物品： 板，CD，文檔，電源
產品目錄頁面： 1114 (CN2011-ZH PDF)
相關產品： 576-3076-ND - IC MAC CTLR 2PORT ETH 100-LFBGA
KSZ8842-32MQLA6-ND - IC SWITCH 10/100 32BIT 128PQFP
576-1479-ND - IC SWITCH 10/100 32BIT 128PQFP
576-1478-5-ND - IC SWITCH 10/100 16BIT 128PQFP
其它名稱： 576-1634
Micrel, Inc.
KSZ8842-16/32 MQL/MVL/MVLI/MBL
October 2007
45
M9999-102207-1.9
IGMP Support
For Internet Group Management Protocol (IGMP) support in Layer 2, the KSZ8842M provides two components:
“IGMP” Snooping
The KSZ8842M traps IGMP packets and forwards them only to the processor (host port). The IGMP packets are
identified as IP packets (either Ethernet IP packets, or IEEE 802.3 SNAP IP packets) with IP version = 0x4 and protocol
version number = 0x2.
“Multicast Address Insertion” in the Static MAC Table
Once the multicast address is programmed in the Static MAC Table, the multicast session is trimmed to the subscribed
ports, instead of broadcasting to all ports.
IPv6 MLD Snooping
The KSZ8842M traps IPv6 Multicast Listener Discovery (MLD) packets and forwards them only to the processor (host
port). MLD snooping is controlled by SGCR2[13] (MLD snooping enable) and SGCR2[12] (MLD option).
Setting SGCR2[13] causes the KSZ8842M to trap packets that meet all of the following conditions:
IPv6 multicast packets
Hop count limit = 1
IPv6 next header = 1 or 58 (or = 0 with hop-by-hop next header = 1 or 58)
If SGCR2[12] = 1, IPv6 next header = 43, 44, 50, 51, or 60 (or =0 with hop-by-hop next header = 43, 44, 50, 51,
or 60)
Port Mirroring Support
KSZ8842M supports “Port Mirroring” comprehensively as:
“receive only” mirror on a port
All the packets received on the port are mirrored on the sniffer port. For example, port 1 is programmed to be “receive
sniff” and the host port is programmed to be the “sniffer port”. A packet received on port 1 is destined to port 2 after the
internal lookup. The KSZ8842M forwards the packet to both port 2 and the host port. The KSZ8842M can optionally even
forward “bad” received packets to the “sniffer port”.
“transmit only” mirror on a port
All the packets transmitted on the port are mirrored on the sniffer port. For example, port 1 is programmed to be “transmit
sniff” and the host port is programmed to be the “sniffer port”. A packet received on port 2 is destined to port 1 after the
internal lookup. The KSZ8842M forwards the packet to both port 1 and the host port.
“receive and transmit” mirror on two ports
All the packets received on port A and transmitted on port B are mirrored on the sniffer port. To turn on the “AND” feature,
set register SGCR2, bit 8 to “1”. For example, port 1 is programmed to be “receive sniff”, port 2 is programmed to be
“transmit sniff”, and the host port is programmed to be the “sniffer port”. A packet received on port 1 is destined to port 2
after the internal lookup. The KSZ8842M forwards the packet to both port 2 and the host port.
Multiple ports can be selected as “receive sniff” or “transmit sniff”. In addition, any port can be selected as the “sniffer
port”. All these per port features can be selected through registers P1CR2, P2CR2, and P3CR2 for ports 1, 2, and the
host port, respectively.
IEEE 802.1Q VLAN Support
The KSZ8842M supports 16 active VLANs out of the 4096 possible VLANs specified in the IEEE 802.1Q specification.
KSZ8842M provides a 16-entry VLAN table, which converts the 12-bits VLAN ID (VID) to the 4-bits Filter ID (FID) for
address lookup. If a non-tagged or null-VID-tagged packet is received, the ingress port default VID is used for lookup. In
VLAN mode, the lookup process starts with VLAN table lookup to determine whether the VID is valid. If the VID is not
valid, the packet is dropped and its address is not learned. If the VID is valid, the FID is retrieved for further lookup. The
FID + Destination Address (FID+DA) are used to determine the destination port. The FID + Source Address (FID+SA) are
used for address learning. (See Tables 10 and 11.)
相關PDF資料
PDF描述
222K121-12-0 BOOT MOLDED
NLCV32T-680K-PF INDUCTOR POWER 68UH 1210
0210490359 CABLE JUMPER 1.25MM .229M 28POS
101-1218 KIT APPLCTN RABBITCORE RCM4010
0982660995 CBL 29POS 0.5MM JMPR TYPE A 5"
相關代理商/技術參數
參數描述
KSZ8842-16MVL 功能描述:以太網 IC 2-Port Ethernet Switch/Repeater + Generic (8, 16-bit) bus interface(Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8842-16MVL TR 功能描述:以太網 IC 2-Port Ethernet Switch/Repeater + Generic (8, 16-bit) bus interface(Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8842-16MVL-EVAL 功能描述:BOARD EVALUATION KSZ8842-16MVL RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 主要目的:電源管理，電池充電器 嵌入式:否 已用 IC / 零件:MAX8903A 主要屬性:1 芯鋰離子電池 次要屬性:狀態 LED 已供物品:板
KSZ8842-16MVLI 功能描述:以太網 IC 2-Port Ethernet Switch/Repeater + Generic (8, 16-bit) bus interface(Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8842-16MVLI TR 功能描述:以太網 IC 2-Port Ethernet Switch/Repeater + Generic (8, 16-bit) bus interface(Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*