參數資料
型號： KSZ8841-16MBL
廠商： Micrel Inc
文件頁數： 26/105頁
文件大?。?/td> 0K
描述： IC MAC CTLR 1PORT ETH 100-LBGA
標準包裝： 260
控制器類型： 以太網控制器，MAC
接口： 總線
電源電壓： 3.1 V ~ 3.5 V
工作溫度： 0°C ~ 70°C
安裝類型： 表面貼裝
封裝/外殼： 100-LBGA
供應商設備封裝： 100-LFBGA
包裝： 托盤
產品目錄頁面： 1080 (CN2011-ZH PDF)
其它名稱： 576-3075
Micrel, Inc.
KSZ8841-16/32 MQL/MVL/MBL
October 2007
27
M9999-102207-1.6
Functional Description
The KSZ8841M is a single-chip Fast Ethernet MAC controller consisting of a 10/100 physical layer transceiver (PHY), a
MAC, and a Bus Interface Unit (BIU) that controls the KSZ8841M via an 8-bit, 16-bit, or 32-bit host bus interface.
The KSZ8841M is fully compliant to IEEE802.3u standards.
Functional Overview
Power Management
Power down
The KSZ8841M features a port power-down mode. To save power, the user can power-down the port that is not in use by
setting bit 11 in either P1CR4 or P1MBCR register for this port. To bring the port back up, reset bit 11 in these registers.
In addition, there is a full chip power-down mode PWRDN (pin 36). When this pin is pulled-down, the entire chip powers
down. Transitioning this pin from pull-down to pull-up results in a power up and chip reset.
Wake-on-LAN
Wake-up frame events are used to wake the system whenever meaningful data is presented to the system over the
network. Examples of meaningful data include the reception of a Magic Packet, a management request from a remote
administrator, or simply network traffic directly targeted to the local system. In all of these instances, the network device is
pre-programmed by the policy owner or other software with information on how to identify wake frames from other network
traffic.
A wake-up event is a request for hardware and/or software external to the network device to put the system into a
powered state (working).
A wake-up signal is caused by:
1. Detection of a change in the network link state
2. Receipt of a network wake-up frame
3. Receipt of a Magic Packet
There are also other types of wake-up events that are not listed here as manufacturers may choose to implement these in
their own way.
Link Change
Link status wake events are useful to indicate a change in the network’s availability, especially when this change may
impact the level at which the system should re-enter the sleeping state. For example, a change from link off to link on may
trigger the system to re-enter sleep at a higher level (D2 versus D3
1) so that wake frames can be detected. Conversely, a
transition from link on to link off may trigger the system to re-enter sleep at a deeper level (D3 versus D2) since the
network is not currently available.
Wake-up Packet
Wake-up packets are certain types of packets with specific CRC values that a system recognizes as a ‘wake up’ frame.
The KSZ8841M supports up to four users defined wake-up frames as below:
1. Wake-up frame 0 is defined in registers 0x00-0x0A of Bank 4 and is enabled by bit 0 in wakeup frame control register.
2. Wake-up frame 1 is defined in registers 0x00-0x0A of Bank 5 and is enabled by bit 1 in wakeup frame control register.
3. Wake-up frame 2 is defined in registers 0x00-0x0A of Bank 6 and is enabled by bit 2 in wakeup frame control register.
4. Wake-up frame 4 is defined in registers 0x00-0x0A of Bank 7 and is enabled by bit 3 in wakeup frame control register.
Magic Packet
Magic Packet technology is used to remotely wake up a sleeping or powered off PC on a LAN. This is accomplished by
sending a specific packet of information, called a Magic Packet frame, to a node on the network. When a PC capable of
receiving the specific frame goes to sleep, it enables the Magic Packet RX mode in the LAN controller, and when the LAN
controller receives a Magic Packet frame, it will alert the system to wake up.
1 References to D0, D1, D2, and D3 are power management states defined in a similar fashion to the way they are defined for PCI. For
more information, refer to the PCI specification at www.pcisig.com/specifications/conventional/pcipm1.2.pdf.
相關PDF資料
PDF描述
PIC12LCE518-04I/SM IC MCU OTP 512X12 LV W/EE 8-SOIJ
PIC12CE519T-04/SN IC MCU OTP 1KX12 W/EE 8SOIC
KSZ8841-16MQL IC MAC CTRLR 8/16BIT 128-PQFP
PIC12CE518-04E/SM IC MCU OTP 512X12 W/EE 8-SOIC
KSZ8895RQ IC 10/100-T 5 PORT SW 128PQFP
相關代理商/技術參數
參數描述
KSZ8841-16MBL-EVAL 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:Single-Port Ethernet MAC Controller with Non-PCI Interface
KSZ8841-16MBLI 功能描述:以太網 IC 10/100BT Ethernet MAC + PHY with Generic (8, 16-Bit) Bus Interface (I-Temp) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8841-16MQL 功能描述:以太網 IC Single Ethernet Port + Generic (8, 16-bit) bus interface( Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8841-16MQL A6 功能描述:IC MAC CTRLR 8/16BIT 128-PQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN（6x6） 包裝:* 其它名稱:Q6396337A
KSZ8841-16MQL-EVAL 功能描述:以太網開發工具 KSZ8841-16MQL Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*