- 您現在的位置：買賣IC網 > PDF目錄16549 > KSZ8031RNL-EVAL (Micrel Inc)BOARD EVALUATION FOR KSZ8031RNL PDF資料下載
參數資料
| 型號： | KSZ8031RNL-EVAL |
| 廠商： | Micrel Inc |
| 文件頁數： | 15/43頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVALUATION FOR KSZ8031RNL |
| 標準包裝： | 1 |
| 主要目的： | 接口，以太網 PHY |
| 嵌入式： | 否 |
| 已用 IC / 零件： | KSZ8031RNL |
| 已供物品： | 板 |
| 相關產品： | 576-3843-6-ND - TXRX PHY 100BASE TX 3.3V 24QFN 576-3843-1-ND - TXRX PHY 100BASE TX 3.3V 24QFN 576-3788-ND - TXRX PHY 10/100 3.3V 24-QFN 576-3843-2-ND - TXRX PHY 100BASE TX 3.3V 24QFN 576-3741-5-ND - TXRX PHY 100BASE TX 3.3V 24QFN |
| 其它名稱： | 576-3862 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁
Micrel, Inc.
KSZ8021RNL / KSZ8031RNL
August 2010
22
M9999-082710-1.0
NAND Tree I/O Testing
The following procedure can be used to check for faults on the KSZ8021/31RNL digital I/O pin connections to the board:
1. Enable NAND tree mode by setting register 16h, bit [5] to ‘1’.
2. Use board logic to drive all KSZ8021/31RNL NAND tree input pins high.
3. Use board logic to drive each NAND tree input pin, per KSZ8021/31RNL NAND Tree pin order, as follow:
a. Toggle the first pin (MDIO) from high to low, and verify the TXD1 pin switch from low to high to indicate
that the first pin is connected properly.
b. Leave the first pin (MDIO) low.
c. Toggle the second pin (MDC) from high to low, and verify the TXD1 pin switch from high to low to indicate
that the second pin is connected properly.
d. Leave the first pin (MDIO) and the second pin (MDC) low.
e. Toggle the third pin from high to low, and verify the TXD1 pin switch from low to high to indicate that the
third pin is connected properly.
f.
Continue with this sequence until all KSZ8021/31RNL NAND tree input pins have been toggled.
Each KSZ8021/31RNL NAND tree input pin must cause the TXD1 output pin to toggle high-to-low or low-to-high to
indicate a good connection. If the TXD1 pin fails to toggle when the KSZ8021/31RNL input pin toggles from high to low,
then the input pin has a fault.
Power Management
The KSZ8021/31RNL offers the following power management modes:
Power Saving Mode
Power Saving Mode is used to reduce the transceiver power consumption when the cable is unplugged. It is enabled by
writing a one to register 1Fh, bit [10], and is in effect when auto-negotiation mode is enabled and cable is disconnected
(no link).
In this mode, the KSZ8021/31RNL turns off all transceiver blocks, except for transmitter, energy detect and PLL circuits.
By default, Power Saving Mode is disabled after power-up.
Energy Detect Power Down Mode
Energy Detect Power Down (EDPD) Mode is used to further reduce the transceiver power consumption when the cable is
un-plugged. It is enabled by writing a zero to register 18h, bit [11], and is in effect when auto-negotiation mode is enabled
and cable is disconnected (no link).
EDPD Mode works in conjunction with PLL off (set by writing a one to register 10h, bit [4] to turn PLL off automatically in
EDPD Mode) to turn off all KSZ8021/31RNL transceiver blocks, except for transmitter and energy detect circuits.
Further power consumption is achieved by extending the time interval in between transmissions of link pulses to check for
the presence of a link partner. The periodic transmission of link pulses is needed to ensure two link partners in the same
low power state and with auto MDI/MDI-X disabled can wake up when the cable is connected between them.
By default, Energy Detect Power Down Mode is disabled after power-up.
Power Down Mode
Power Down Mode is used to power down the KSZ8021/31RNL device when it is not in use after power-up. It is enabled
by writing a one to register 0h, bit [11].
In this mode, the KSZ8021/31RNL disables all internal functions, except for the MII management interface. The
KSZ8021/31RNL exits (disables) Power Down Mode after register 0h, bit [11] is set back to zero.
相關PDF資料 |
PDF描述 |
|---|---|
| HBM10DRTF | CONN EDGECARD 20POS DIP .156 SLD |
| H3BKH-5006G | IDC CABLE - HSR50H/AE50G/HPK50H |
| GCM25DTKN | CONN EDGECARD 50POS DIP .156 SLD |
| ESC10DRYI-S13 | CONN EDGECARD 20POS .100 EXTEND |
| GCM25DTKH | CONN EDGECARD 50POS DIP .156 SLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KSZ8031RNLI | 功能描述:TXRX PHY 10/100 3.3V 24-QFN RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,140 系列:AU 類型:收發器 驅動器/接收器數:1/1 規程:CAN 電源電壓:5.3 V ~ 27 V 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SO 包裝:管件 其它名稱:935267940512AU5790D14AU5790D14-ND |
| KSZ8031RNLI TR | 功能描述:以太網 IC 3.3V, 10Base-T/100Base-TX Physical Layer Transceiver w/ RMII Support (24-QFN, Industrial Grade) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8031RNLITR | 制造商:Micrel Inc 功能描述:Ethernet transceiver,PHY,RMII,QFN24 |
| KSZ8031RNLI-TR | 功能描述:1/1 Transceiver Full RMII 24-QFN (4x4) 制造商:microchip technology 系列:- 包裝:剪切帶（CT） 零件狀態:過期 類型:收發器 協議:RMII 驅動器/接收器數:1/1 雙工:全 接收器滯后:- 數據速率:- 電壓 - 電源:1.8V，2.5V，3.3V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商器件封裝:24-QFN（4x4） 標準包裝:1 |
| KSZ8031RNL-TR | 功能描述:1/1 Transceiver Full RMII 24-QFN (4x4) 制造商:microchip technology 系列:- 包裝:剪切帶（CT） 零件狀態:過期 類型:收發器 協議:RMII 驅動器/接收器數:1/1 雙工:全 接收器滯后:- 數據速率:- 電壓 - 電源:1.8V，2.5V，3.3V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商器件封裝:24-QFN（4x4） 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。