- 您現在的位置：買賣IC網 > PDF目錄374353 > KM29W040AIT (SAMSUNG SEMICONDUCTOR CO. LTD.) 512K x 8 Bit NAND Flash Memory(512K x 8位 NAND閃速存儲器) PDF資料下載
參數資料
| 型號： | KM29W040AIT |
| 廠商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | 512K x 8 Bit NAND Flash Memory(512K x 8位 NAND閃速存儲器) |
| 中文描述： | 為512k × 8位NAND閃存（為512k × 8位的NAND閃速存儲器） |
| 文件頁數： | 19/21頁 |
| 文件大?。?/td> | 218K |
| 代理商： | KM29W040AIT |
KM29W040AT, KM29W040AIT
FLASH MEMORY
19
Figure 7. RESET Operation
READY/BUSY
The device has a R/B output that provides a hardware method of indicating the completion of a frame program, erase or read seek
completion. The R/B pin is normally high but transitions to low after program or erase command is written to the command register or
a random read is begin after address loading. It returns to high when the internal controller has finished the operation. The pi n is an
open-drain driver thereby allowing two or more R/ B outputs to be Or-tied. An appropriate pull-up resister is required for proper opera-
tion and the value may be calculated by following equation.
RESET
The device offers a reset feature, executed by writing FFH to the command register. When the device is in Busy state during the
read, program or erase mode, the reset operation will abort these operation. In the case of Reset during Program or Erase opera-
tions, the contents of memory cells being altered are no longer valid, as the data will be partially programmed or erased. The d evice
enters the Read mode after completion of Reset operation as shown Table 3. If the device is already in reset state a new reset com-
mand will not be accepted to by the command register. The R/ B pin transitions to low for t
RST
after the Reset command is written.
Reset command is not necessarily for normal device operation. Refer to Figure 7 below.
After Power-up
After Reset
Operation Mode
Read
Read
FFH
I/O
0
~
7
R/B
Rp =
V
CC
R/B
open drain output
Device
GND
V
CC
(Max.) - V
OL
(Max.)
I
OL
+
Σ
I
L
=
Note*
8mA
+
Σ
I
L
where I
L
is the sum of the input currents of all devices tied to the
R/B pin.
Table3. Device Status
Note* KM29N040 ; 5.1V
KM29V040 ; 3.2V
KM29W040A ; 5.1V when Vcc=3.6V~5.5V
3.2V when Vcc=3.0V~3.6V
t
RST
相關PDF資料 |
PDF描述 |
|---|---|
| KM29W16000AIT | 2M x 8 Bit NAND Flash Memory(2M x 8位 NAND閃速存儲器) |
| KM29W16000AT | 2M x 8 Bit NAND Flash Memory(2M x 8位 NAND閃速存儲器) |
| KM29W16000ATS | 2M x 8 Bit NAND Flash Memory(2M x 8位 NAND閃速存儲器) |
| KM29W32000AIT | 4M x 8 Bit NAND Flash Memory(4M x 8 位 NAND閃速存儲器) |
| KM29W32000AT | 4M x 8 Bit NAND Flash Memory(4M x 8 位 NAND閃速存儲器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KM29W040AT | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:512K x 8 bit NAND Flash Memory |
| KM2M COMBO-L | 制造商:Micro-Star International 功能描述:KM266 UATX AMD 266FSB DDR - Bulk |
| KM2M806XT | 制造商:Kontron 功能描述:M2M DEPLOYMENT UNIT FOR APPLICATIONS IN HARSH ENVIRONMENTS - Boxed Product (Development Kits) |
| KM2M810-01 | 制造商:Kontron 功能描述:FRI 2.0 DEVELOPMENT KIT WITHOUT THE ERICSSON MODEM - Boxed Product (Development Kits) |
| KM2M810-02 | 制造商:Kontron 功能描述:FRI 2.0 DEVELOPMENT KIT WITH ERICSSON MODEM - Boxed Product (Development Kits) |
發布緊急采購，3分鐘左右您將得到回復。