OPERATIONAL MODES Figure 22. CAN Bus Signal" />
參數資料
型號： KIT33742DWEVB
廠商： Freescale Semiconductor
文件頁數： 36/71頁
文件大小： 0K
描述： KIT FOR 33742 SBC WITH EHSCAN
標準包裝： 1
主要目的： 接口，CAN 控制器
已用 IC / 零件： MC33742
相關產品： MC33742DW-ND - IC SYSTEM BASE W/LIN 28-SOIC
MC33742DWR2-ND - IC SYSTEM BASE W/LIN 28-SOIC
MC33742SDW-ND - IC SYSTEM BASE W/LIN 28-SOIC
MC33742SDWR2-ND - IC SYSTEM BASE W/LIN 28-SOIC
Analog Integrated Circuit Device Data
Freescale Semiconductor
41
33742
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
Figure 22. CAN Bus Signal During Can Sleep State and Wake-up Sequence
Figure 23 illustrates how the wake-up signal is generated. First the CAN signal is detected by a low consumption receiver (WU
receiver). Then the signal passes through a pulse width filter, which discards the undesired pulses. The pulse must have a width
bigger than 0.5
s and smaller than 500 s to be accepted. When a pulse is discarded, the pulse counter is reset and no wake-
up signal is generated. When a pulse is accepted, the pulse counter is incremented and, after three pulses, the internal wake-up
signal is asserted.
Each one of the pulses must be spaced by no more than 500
s. If not, the counter will be reset and no wake-up signal will be
generated. This is accomplished by the wake-up timeout generator. The wake-up cycle is completed (and the wake-up flag reset)
when the CAN interface is brought to CAN Normal mode.
Figure 23. Wake-up Functional Block Diagram
CAN WAKE-UP REPORT
The CAN wake-up reporting depend upon the low power mode the SBC is in.
If the SBC is placed into Sleep mode (VDD and V2 off), the CAN wake-up or any wake-up results in the VDD regulator turning
on, leading to turning on the MCU supply and releasing reset. If the 33742 is in Stop mode (V2 off and VDD active), the CAN
wake-up or any wake-up is signalled by a pulse on the INT output. In addition the CANWU bit is set in the CAN register.
If the SBC is in Normal or Standby mode and the CAN interface is in Sleep mode with wake-up enabled, the CAN wake-up is
reported by the CANWU bit in the CAN register.
In the event the SBC is in Normal mode and CAN Sleep mode with wake-up enabled, it is recommended that the user check
for the CANWU bit prior to placing the 33742 in Sleep or Stop mode in case bus traffic has occurred while the CAN interface was
in Sleep mode.
CANL
CANH
TXD
RXD
Ground
2.5 V
CANL Dominant
CANH Dominant
CANL/CANH Recessive
CAN in TXRX Mode
CAN in Sleep Mode (Wake-up Enable)
Incoming CAN Message
CANL Dominant
CANH Dominant
CANL Dominant
CANH Dominant
CANL Dominant
CANH Dominant
WU Receiver
Internal Wake-up Signal
Min 500 ns
Max 500
s
CAN Bus Sleep State
Pulse # 1
Pulse # 2
Pulse # 3
+
Internal Wake-up
Latch
RST
Timeout
RST
Counter
Pulse OK
Narrow
Pulse
Pulse Width
Filter
Timeout
Generator
Standby
WU Receiver
CANH
CANL
Signal
相關PDF資料
PDF描述
EGM12DTBS-S189 CONN EDGECARD 24POS R/A .156 SLD
EBM28DTBS-S189 CONN EDGECARD 56POS R/A .156 SLD
ESM12DTAS-S189 CONN EDGECARD 24POS R/A .156 SLD
EGM12DTAS-S189 CONN EDGECARD 24POS R/A .156 SLD
EBM28DTAS-S189 CONN EDGECARD 56POS R/A .156 SLD
相關代理商/技術參數
參數描述
KIT3376MMA7330L 功能描述:加速傳感器開發工具 XYZ-AXIS ANALOG ACCELERO RoHS:否 制造商:Murata 工具用于評估:SCA3100-D04 加速:2 g 傳感軸:Triple Axis 接口類型:SPI 工作電壓:3.3 V
KIT3376MMA7331L 功能描述:加速傳感器開發工具 3-AXIS ANALOG OUT 4g /12g Dev Kit RoHS:否 制造商:Murata 工具用于評估:SCA3100-D04 加速:2 g 傳感軸:Triple Axis 接口類型:SPI 工作電壓:3.3 V
KIT3376MMA7331LC 功能描述:加速傳感器開發工具 3AXIS Angl Accelero Eval Kit RoHS:否 制造商:Murata 工具用于評估:SCA3100-D04 加速:2 g 傳感軸:Triple Axis 接口類型:SPI 工作電壓:3.3 V
KIT3376MMA7340L 功能描述:加速傳感器開發工具 XYZ-AXIS ANALOG ACCELERO RoHS:否 制造商:Murata 工具用于評估:SCA3100-D04 加速:2 g 傳感軸:Triple Axis 接口類型:SPI 工作電壓:3.3 V
KIT3376MMA7341L 功能描述:加速傳感器開發工具 3-AXIS ANALOG OUT 3g /11g Dev Kit RoHS:否 制造商:Murata 工具用于評估:SCA3100-D04 加速:2 g 傳感軸:Triple Axis 接口類型:SPI 工作電壓:3.3 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*