參數資料
型號： ISPPAC-POWR1014A-01TN48I
廠商： LATTICE SEMICONDUCTOR CORP
元件分類： 電源管理
英文描述： In-System Programmable Power Supply Supervisor, Reset Generator and Sequencing Controller
中文描述： 10-CHANNEL POWER SUPPLY SUPPORT CKT, PQFP48
封裝： LEAD FREE, TQFP-48
文件頁數： 36/45頁
文件大小： 999K
代理商： ISPPAC-POWR1014A-01TN48I
Lattice Semiconductor
ispPAC-POWR1014/A Data Sheet
36
Figure 30. TAP States
When the correct logic sequence is applied to the TMS and TCK inputs, the TAP will exit the Test-Logic-Reset state
and move to the desired state. The next state after Test-Logic-Reset is Run-Test/Idle. Until a data or instruction shift
is performed, no action will occur in Run-Test/Idle (steady state = idle). After Run-Test/Idle, either a data or instruc-
tion shift is performed. The states of the Data and Instruction Register blocks are identical to each other differing
only in their entry points. When either block is entered, the first action is a capture operation. For the Data Regis-
ters, the Capture-DR state is very simple: it captures (parallel loads) data onto the selected serial data path (previ-
ously chosen with the appropriate instruction). For the Instruction Register, the Capture-IR state will always load
the IDCODE instruction. It will always enable the ID Register for readout if no other instruction is loaded prior to a
Shift-DR operation. This, in conjunction with mandated bit codes, allows a “blind” interrogation of any device in a
compliant IEEE 1149.1 serial chain. From the Capture state, the TAP transitions to either the Shift or Exit1 state.
N
ormally the Shift state follows the Capture state so that test data or status information can be shifted out or new
data shifted in. Following the Shift state, the TAP either returns to the Run-Test/Idle state via the Exit1 and Update
states or enters the Pause state via Exit1. The Pause state is used to temporarily suspend the shifting of data
through either the Data or Instruction Register while an external operation is performed. From the Pause state,
shifting can resume by reentering the Shift state via the Exit2 state or be terminated by entering the Run-Test/Idle
state via the Exit2 and Update states. If the proper instruction is shifted in during a Shift-IR operation, the next entry
into Run-Test/Idle initiates the test mode (steady state = test). This is when the device is actually programmed,
erased or verified. All other instructions are executed in the Update state.
Test Instructions
Like data registers, the IEEE 1149.1 standard also mandates the inclusion of certain instructions. It outlines the
function of three required and six optional instructions. Any additional instructions are left exclusively for the manu-
facturer to determine. The instruction word length is not mandated other than to be a minimum of two bits, with only
the BYPASS and EXTEST instruction code patterns being specifically called out (all ones and all zeroes respec-
tively). The ispPAC-POWR1014/A contains the required minimum instruction set as well as one from the optional
instruction set. In addition, there are several proprietary instructions that allow the device to be configured and ver-
ified. Table 11 lists the instructions supported by the ispPAC-POWR1014/A JTAG Test Access Port (TAP) controller:
Test-Logic-Rst
Run-Test/Idle
Select-DR-Scan
Select-IR-Scan
Capture-DR
Capture-IR
Shift-DR
Shift-IR
Exit1-DR
Exit1-IR
Pause-DR
Pause-IR
Exit2-DR
Exit2-IR
Update-DR
Update-IR
1
0
0
0
0
0
0
0
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
1
1
1
1
1
0
N
ote: The value shown adjacent to each state transition in this figure
represents the signal present at TMS at the time of a rising edge at TCK.
相關PDF資料
PDF描述
ISPPAC-POWR6AT6-01N32I In-System Programmable Power Supply Monitoring and Margining Controller
ISPPAC-POWR6AT6-01NN32I In-System Programmable Power Supply Monitoring and Margining Controller
ISPPAC10 In-System Programmable Analog Circuit
ISPPAC10-01PI In-System Programmable Analog Circuit
ISPPAC10-01SI In-System Programmable Analog Circuit
相關代理商/技術參數
參數描述
ISPPACPOWR1014A01TN48IAG6 制造商:Lattice Semiconductor Corporation 功能描述:
ispPAC-POWR1014A-02T48I 功能描述:監控電路 ispPAC-POWR1014 w/ ADC INDLOG DEV(ECP3) RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
ispPAC-POWR1014A-02TN48I 功能描述:監控電路 ispPAC-POWR1014 w/ ADC, IND, Pb-Free RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
ISPPACPOWR120801T44E 制造商:Lattice Semiconductor Corporation 功能描述:
ISPPAC-POWR1208-01T44E 功能描述:監控電路 PROGRAMMABLE PWR SUPPLY CONTR RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*