參數資料
型號： ISPPAC-CLK5620V-01TN48I
廠商： Lattice Semiconductor Corporation
英文描述： Backlight LED; Color:Red; Digit/Alpha Height:85mm; Forward Current:500mA; Operating Temperature Range:0 C to +50 C; Leaded Process Compatible:No; Light Emitting Area:85x220mm; Peak Reflow Compatible (260 C):No
中文描述： 在系統可編程，零延遲時鐘發生器通用扇出緩沖器
文件頁數： 31/47頁
文件大?。?/td> 871K
代理商： ISPPAC-CLK5620V-01TN48I
Lattice Semiconductor
ispClock5600 Family Data Sheet
31
Pro
fi
le Select
The ispClock5600 stores all internal con
fi
guration data in on-board E
2
CMOS memory. Up to four independent con-
fi
guration pro
fi
les may be stored in each device. The choice of which con
fi
guration pro
fi
le is to be active is speci
fi
ed
thought the pro
fi
le select inputs PS0 and PS1, as shown in Table 7.
Table 7. Profile Select Function
Each pro
fi
le controls the following internal con
fi
guration items:
M divider setting
N divider setting
V divider settings
PLL loop
fi
lter settings
Output skew settings
Internal feedback skew settings
Internal vs. external feedback selection
The following settings are independent of the selection of active pro
fi
le and will apply regardless of which pro
fi
le is
selected:
Input logic con
fi
guration
– Logic family
– Input impedance
Output bank logic con
fi
guration
– Logic family
– V-Divider signal source
– Enable/SGATE control options
– Output impedance
– Slew rate
– Signal inversion
V-Divider to be used as feedback source
Fine/Coarse skew mode selection
UES string
If any of the above items are modi
fi
ed, the change will apply across all pro
fi
les. In some cases this may cause
unanticipated behavior. If multiple pro
fi
les are used in a design, the suitability of the pro
fi
le independent settings
must be considered with respect to each of the individual pro
fi
les.
When a pro
fi
le is changed by modifying the values of the PS0 and PS1 inputs, it may be necessary to assert a
RESET signal to the ispClock5600 to restart the PLL and resynchronize all the internal dividers.
RESET and Power-up Functions
To ensure proper PLL startup and synchronization of outputs, the ispClock5600 provides both internally generated
and user-controllable external reset signals. An internal reset is generated whenever the device is powered up. An
external reset may be applied by asserting a logic HIGH at the RESET pin. Please note that the RESET pin does
not have an internal pull-up or pull-down resistor associated with it and should be tied LOW if not used. Asserting
RESET resets all internal dividers, and will cause the PLL to lose lock. On losing lock, the VCO frequency will begin
dropping. The length of time required to regain lock is related to the length of time for which RESET was asserted.
PS1
PS0
Active Pro
fi
le
0
0
Pro
fi
le 0
0
1
Pro
fi
le 1
1
0
Pro
fi
le 2
1
1
Pro
fi
le 3
相關PDF資料
PDF描述
ISPPAC-POWR1014 In-System Programmable Power Supply Supervisor, Reset Generator and Sequencing Controller
ISPPAC-POWR1014-01T48I In-System Programmable Power Supply Supervisor, Reset Generator and Sequencing Controller
ISPPAC-POWR1014-01TN48I In-System Programmable Power Supply Supervisor, Reset Generator and Sequencing Controller
ISPPAC-POWR1014A In-System Programmable Power Supply Supervisor, Reset Generator and Sequencing Controller
ISPPAC-POWR1014A-01T48I In-System Programmable Power Supply Supervisor, Reset Generator and Sequencing Controller
相關代理商/技術參數
參數描述
ISPPAC-POWR1014 制造商:LATTICE 制造商全稱:Lattice Semiconductor 功能描述:In-System Programmable Power Supply Supervisor, Reset Generator and Sequencing Controller
ISPPAC-POWR1014_08 制造商:LATTICE 制造商全稱:Lattice Semiconductor 功能描述:In-System Programmable Power Supply Supervisor, Reset Generator and Sequencing Controller
ispPAC-POWR1014-01T48I 功能描述:監控電路 Prec. Prog. Pwr Sppl y Seq. Mon. Trim I RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
ISPPAC-POWR1014-01TN148I 制造商:Lattice Semiconductor Corporation 功能描述:#WR MGR ISP RESET & SEQ CNTRL 48TQFP
ispPAC-POWR1014-01TN48I 功能描述:監控電路 Prec. Prog. Pwr Sppl y Seq. Mon. Trim I RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*