- 您現在的位置：買賣IC網 > PDF目錄383164 > ISL6721 (Intersil Corporation) Flexible Single Ended Current Mode PWM Controller(靈活的單端電流模式PWM控制器) PDF資料下載
參數資料
| 型號： | ISL6721 |
| 廠商： | Intersil Corporation |
| 英文描述： | Flexible Single Ended Current Mode PWM Controller(靈活的單端電流模式PWM控制器) |
| 中文描述： | 靈活的單端電流模式PWM控制器（靈活的單端電流模式的PWM控制器） |
| 文件頁數： | 12/21頁 |
| 文件大小： | 416K |
| 代理商： | ISL6721 |
12
FN9110.5
July 20, 2007
Ground Plane Requirements
Careful layout is essential for satisfactory operation of the
device. A good ground plane must be employed. A unique
section of the ground plane must be designated for high di/dt
currents associated with the output stage. Power ground
(PGND) can be separated from the logic ground (LGND) and
connected at a single point. V
C
should be bypassed directly
to PGND with good high frequency capacitors. The return
connection for input power and the bulk input capacitor
should be connected to the PGND ground plane.
Reference Design
The Typical Application Schematic features the ISL6721 in a
conventional dual output 10W discontinuous mode flyback
DC/DC converter. The ISL6721EVAL1 demonstration unit
implements this design and is available for evaluation.
The input voltage range is from 36VDC to 75VDC, and the
two outputs are 3.3V @ 2.5A and 1.8V @ 1.0A. Cross
regulation is achieved using the weighted sum of the two
outputs.
Circuit Element Descriptions
The converter design may be broken down into the following
functional blocks:
Input Storage and Filtering Capacitance: C
1
, C
2
, C
3
Isolation Transformer: T1
Primary voltage Clamp: C
R6
, R
24
, C
18
Start Bias Regulator: R
1
, R
2
, R
6
, Q
3
, V
R1
Operating Bias and Regulator: R
25
, Q
2
, D
1
, C
5
, C
R2
, D
2
Main MOSFET Power Switch: Q
1
Current Sense Network: R
4
, R
3
, R
23
, C
4
Feedback Network:, R
13
, R
15
, R
16
, R
17
, R
18
, R
19
, R
20
,
R
26
, R
27
, C
13
, C
14
, U
2
, U
3
Control Circuit:C
7
, C
8
, C
9
, C
10
, C
11
, C
12
, R
5
, R
6
, R
8
, R
9
,
R
10
, R
11
, R
12
, R
14
, R
22
Output Rectification and Filtering: C
R4
, C
R5
, C
15
, C
16
, C
19
,
C
20
, C
21
, C
22
Secondary Snubber: R
21
, C
17
Design Criteria
The following design requirements were selected:
Switching Frequency, f
sw
: 200kHz
V
IN
: 36V to 75V
V
OUT(1)
: 3.3V @ 2.5A
V
OUT(2)
: 1.8V @ 1.0A
V
OUT(BIAS)
: 12V @ 50mA
P
OUT
: 10W
Efficiency: 70%
Maximum Duty Cycle, D
MAX
: 0.45
Transformer Design
The design of a flyback transformer is a non-trivial affair. It is
an iterative process which requires a great deal of
experience to achieve the desired result. It is a process of
many compromises, and even experienced designers will
produce different designs when presented with identical
requirements. The iterative design process is not presented
here for clarity.
The abbreviated design process follows:
Select a core geometry suitable for the application.
Constraints of height, footprint, mounting preference, and
operating environment will affect the choice.
Select suitable core material(s).
Select maximum flux density desired for operation.
Select core size. Core size will be dictated by the
capability of the core structure to store the required
energy, the number of turns that have to be wound, and
the wire gauge needed. Often the window area (the space
used for the windings) and power loss determine the final
core size. For flyback transformers, the ability to store
energy is the critical factor in determining the core size.
The cross sectional area of the core and the length of the
air gap in the magnetic path determine the energy storage
capability.
Determine maximum desired flux density. Depending on
the frequency of operation, the core material selected, and
the operating environment, the allowed flux density must
be determined. The decision of what flux density to allow
is often difficult to determine initially. Usually the highest
flux density that produces an acceptable design is used,
but often the winding geometry dictates a larger core than
is required based on flux density and energy storage
calculations.
Determine the number of primary turns.
Determine the turns ratio.
Select the wire gauge for each winding.
Determine winding order and insulation requirements.
Verify the design.
Input Power:
P
OUT
/Efficiency = 14.3W (use 15W)
Max On Time: t
ON(MAX)
= D
MAX
/f
sw
= 2.25
μ
s
Average Input Current: I
AVG(IN)
= P
IN
/V
IN(MIN)
= 0.42A
Peak Primary Current:
I
PPK
2
I
ON MAX
sw
)
----------------------------------------
1.87
=
=
A
(EQ. 9)
ISL6721
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6722A | 1024 x 9 x 2 Asynchronous Bidirectional FIFO Memory 44-PLCC 0 to 70 |
| ISL6723AABZ | Flexible Single Ended Current Mode PWM Controllers |
| ISL6722AABZ | 1024 x 9 x 2 Asynchronous Bidirectional FIFO Memory 64-TQFP 0 to 70 |
| ISL6722AAVZ | Flexible Single Ended Current Mode PWM Controllers |
| ISL6722AAVZ-T | Flexible Single Ended Current Mode PWM Controllers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6721AARZ | 功能描述:IC REG CTRLR BST FLYBK ISO 16QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6721AARZ-T | 功能描述:IC REG CTRLR BST FLYBK ISO 16QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6721AAVZ | 功能描述:IC REG CTRLR PWM CM 16-TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6721AAVZ-T | 功能描述:IC REG CTRLR PWM CM 16-TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6721AB | 功能描述:IC REG CTRLR PWM CM 16-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:100% 電源電壓:8.2 V ~ 30 V 降壓:無 升壓:無 回掃:是 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:0°C ~ 70°C 封裝/外殼:8-DIP（0.300"，7.62mm） 包裝:管件 產品目錄頁面:1316 (CN2011-ZH PDF) |
發布緊急采購，3分鐘左右您將得到回復。