參數資料
型號： ISL6721
廠商： Intersil Corporation
英文描述： Flexible Single Ended Current Mode PWM Controller(靈活的單端電流模式PWM控制器)
中文描述： 靈活的單端電流模式PWM控制器（靈活的單端電流模式的PWM控制器）
文件頁數： 10/21頁
文件大?。?/td> 416K
代理商： ISL6721
10
FN9110.5
July 20, 2007
The total supply current (I
C
plus I
CC
) will be higher,
depending on the load applied to GATE. Total current is the
sum of the quiescent current and the average gate current.
Knowing the operating frequency, f
sw
, and the MOSFET
gate charge, Qg, the average GATE output current can be
calculated in Equation 5:
VREF -
The 5V reference voltage output. Bypass to LGND
with a 0.01
μ
F or larger capacitor to filter this output as
needed. Using capacitance less than this value may result in
unstable operation.
SS -
Connect the soft-start capacitor between this pin and
LGND to control the duration of soft-start. The value of the
capacitor determines both the rate of increase of the duty
cycle during start up, and also controls the overcurrent
shutdown delay.
ISET -
A DC voltage between 0.35V and 1.2V applied to this
input sets the pulse-by-pulse overcurrent threshold. When
overcurrent inception occurs, the SS capacitor begins to
discharge and starts the overcurrent delayed shutdown
cycle.
Functional Description
Features
The ISL6721 current mode PWMs make an ideal choice for
low-cost flyback and forward topology applications requiring
enhanced control and supervisory capability. With adjustable
overvoltage and undervoltage thresholds, overcurrent
threshold, and hic-cup delay, a highly flexible design with
minimal external components is possible. Other features
include peak current mode control, adjustable soft-start,
slope compensation, adjustable oscillator frequency, and a
bi-directional synchronization clock input.
Oscillator
The ISL6721 have a sawtooth oscillator with a
programmable frequency range to 1MHz, which can be
programmed with a resistor and capacitor on the RTCT pin.
(Please refer to
Figure
4
for the resistance and capacitance
required for a given frequency.)
Implementing Synchronization
The oscillator can be synchronized to an external clock
applied at the SYNC pin or by connecting the SYNC pins of
multiple ICs together. If an external master clock signal is
used, it must be at least 65% of the free running frequency of
the oscillator for proper synchronization. The external
master clock signal should have a pulse width greater than
20ns. If no master clock is used, the first device to assert
SYNC assumes control of the SYNC signal. An external
SYNC pulse is ignored if it occurs during the first 1/3 of the
switching cycle.
During normal operation the RTCT voltage charges from 1.5
to 3.0V and back during each cycle. Clock and SYNC
signals are generated when the 3.0V threshold is reached. If
an external clock signal is detected during the latter 2/3 of
the charging cycle, the oscillator switches to external
synchronization mode and relies upon the external SYNC
signal to terminate the oscillator cycle. The generation of a
SYNC signal is inhibited in this mode. If the RTCT voltage
exceeds 4.0V (i.e. no external SYNC signal terminates the
cycle), the oscillator reverts to the internal clock mode and a
SYNC signal is generated.
Soft-Start Operation
The ISL6721 features soft-start using an external capacitor
in conjunction with an internal current source. Soft-start is
used to reduce voltage stresses and surge currents during
start up.
Upon start up, the soft-start circuitry clamps the error
amplifier output (COMP pin) to a value proportional to the
soft-start voltage. The error amplifier output rises as the soft-
start capacitor voltage rises. This has the effect of increasing
the output pulse width from zero to the steady state
operating duty cycle during the soft-start period. When the
soft-start voltage exceeds the error amplifier voltage, soft-
start is completed. Soft-start forces a controlled output
voltage rise. Soft-start occurs during start-up and after
recovery from a fault condition or overcurrent shutdown. The
soft-start voltage is clamped to 4.5V.
Gate Drive
The ISL6721 is capable of sourcing and sinking 1A peak
current. Separate collector supply (V
C
) and power ground
(PGnd) pins help isolate the IC’s analog circuitry from the
high power gate drive noise. To limit the peak current
through the IC, an external resistor may be placed between
the totem-pole output of the IC (GATE pin) and the gate of
the MOSFET. This small series resistor also damps any
oscillations caused by the resonant tank of the parasitic
inductances in the traces of the board and the FET’s input
capacitance.
Slope Compensation
For applications where the maximum duty cycle is less than
50%, slope compensation may be used to improve noise
immunity, particularly at lighter loads. The amount of slope
compensation required for noise immunity is determined
empirically, but is generally about 10% of the full scale
current feedback signal. For applications where the duty
cycle is greater than 50%, slope compensation is required to
prevent instability. Slope compensation is a technique in
which the current feedback signal is modified by adding
additional slope to it. The minimum amount of slope
compensation required corresponds to 1/2 the inductor
downslope. However, adding excessive slope compensation
results in a control loop that behaves more as a voltage
mode controller than as current mode controller.
(EQ. 5)
Igate
Qg
f
sw
=
A
ISL6721
相關PDF資料
PDF描述
ISL6722A 1024 x 9 x 2 Asynchronous Bidirectional FIFO Memory 44-PLCC 0 to 70
ISL6723AABZ Flexible Single Ended Current Mode PWM Controllers
ISL6722AABZ 1024 x 9 x 2 Asynchronous Bidirectional FIFO Memory 64-TQFP 0 to 70
ISL6722AAVZ Flexible Single Ended Current Mode PWM Controllers
ISL6722AAVZ-T Flexible Single Ended Current Mode PWM Controllers
相關代理商/技術參數
參數描述
ISL6721AARZ 功能描述:IC REG CTRLR BST FLYBK ISO 16QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR)
ISL6721AARZ-T 功能描述:IC REG CTRLR BST FLYBK ISO 16QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR)
ISL6721AAVZ 功能描述:IC REG CTRLR PWM CM 16-TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR)
ISL6721AAVZ-T 功能描述:IC REG CTRLR PWM CM 16-TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR)
ISL6721AB 功能描述:IC REG CTRLR PWM CM 16-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:100% 電源電壓:8.2 V ~ 30 V 降壓:無 升壓:無 回掃:是 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:0°C ~ 70°C 封裝/外殼:8-DIP（0.300"，7.62mm） 包裝:管件 產品目錄頁面:1316 (CN2011-ZH PDF)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*