- 您現在的位置：買賣IC網 > PDF目錄383128 > ISL1219 (Intersil Corporation) Low Power RTC with Battery Backed SRAM and Event Detection(具有電池供電的SRAM和事件檢測功能的低功率RTC) PDF資料下載
參數資料
| 型號： | ISL1219 |
| 廠商： | Intersil Corporation |
| 英文描述： | Low Power RTC with Battery Backed SRAM and Event Detection(具有電池供電的SRAM和事件檢測功能的低功率RTC) |
| 中文描述： | 低功耗RTC與電池供電的SRAM和事件檢測（具有電池供電的SRAM的和事件檢測功能的低功率實時時鐘） |
| 文件頁數： | 20/25頁 |
| 文件大?。?/td> | 373K |
| 代理商： | ISL1219 |
20
FN6314.1
August 14, 2006
Application Section
Event Detection
The event detection feature of the ISL1219 is intended to be
used for recording the time of single events that involve the
opening of an enclosure, door, etc. The normal method of
detection is with normally closed switch function that opens
to initiate the event. This mechanism is ideal for applications
such as set top boxes, utility meters, security alarm and
camera systems or vending machines.
A typical application diagram is shown in Figure 19. A
microcontroller communicates with the ISL1219 through the
I
2
C serial bus, to set up and read time of the day, alarms, or
set up the outputs frequency control.
The ISL1219 is capable of recording individual event
time/dates using the on-chip registers (Event Registers,
addresses 14h to 19h). Single event times are recorded and
can be read using a multiple address read, similar to reading
the RTC registers. The Event Registers record the initial
event time of a series of events, until the EVT bit is reset.
After EVT is reset, the Timestamp Registers retain the
previous event time until the next Event happens, at which
time the current RTC register contents will be placed in the
Event Registers. The Timestamp Registers cannot be
cleared, only a full power down cycle (Vcc and Vbat = 0V)
will erase their contents.
For example, the event function is enabled and the EVT bit
in the Status Register is cleared. Then the EVEN pin is
triggered 3 times before the timestamp register is read. Only
the first Event time will be recorded in the Timestamp
Registers, and will be read. Then the EVT bit is cleared in
the Status Register, and two more events happen. The
previous Timestamp contents are replaced by the time of the
next event after the EVT bit reset.
An additional event action available in the ISL1219 is to stop
the real time clock from advancing. If the event register is set
to enable this function (Register 09h, RTCHLT bit 5 set to 1),
then when the EVIN pin is triggered, the clock counters will
stop and hold the time of the event. This is useful for one
time occurrences such as opening a warranted consumer
product enclosure or exceeding a maximum temperature
inside a device. Once the clock is stopped, the clock
registers must be written with an updated time, then they will
begin advancing immediately. If the RTCHLT bit is still set,
then the next event will again stop the clock.
Event Detect Input Details
The EVIN input is a Schmitt trigger logic input. An event is
detected when it is asserted high. The ISL1219 device has
internal configuration settings which add detection flexibility.
There are four configuration bits in register 09h which are for
EVIN sampling. The ESMP1 and ESMP0 bits control
sampling of the event input status. Reducing the sampling
rate will lower the supply current drain, with the tradeoff of
adding a delay in detecting an event. An event that is long in
duration (i.e. opening a door) would obviously be served well
with the lowest frequency sampling rate and lowest supply
current drain.
The EHYS1 and EHYS0 bits control timer circuits to filter out
switch bouncing, noise or intermittent contacts, by effectively
adding time-based hysteresis to the EVIN input. They are
used only in conjunction with the sampling rate, they cannot
P0
P2
P4
P1
P3
P5
SCL
SDA
X1
X2
V
BAT
V
DD
EVIN
V
CC
IRQ/F
SCL
SDA
EVDET
ISL1219
MICRO C.
Event Detect Switch Normally Closed
Source
** The Pull-up resistor on the EVDET-output can vary
from 10k up to 10M or more, depending on the
application
V
CC
5.1k
5.1k+
1M**
2M*
3.0V
32.768kHz
Optional Pull-up resistors, or use internal current
10
9
8
7
6
1
2
3
4
5
FIGURE 19.
ISL1219
相關PDF資料 |
PDF描述 |
|---|---|
| ISL1220 | Low Power RTC with 8 Bytes of Battery Backed SRAM and Separate FOUT(具有電池供電的8位SRAM和獨立輸出的低功率RTC) |
| ISL1221 | Low Power RTC with Battery Backed SRAM and Event Detection(具有電池供電的SRAM和事件檢測功能的低功率RTC) |
| ISL21009 | High Voltage Input Precision, Low Noise FGA Voltage References(高電壓輸入精度，低噪聲FGA電壓基準) |
| ISL21400 | Programmable Temperature Slope Voltage Reference(可編程溫度斜率電壓基準) |
| ISL22316 | Low Noise, Low Power I2C Bus, 128 Taps(低噪聲,低功率，I2C總線, 128抽頭電位器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL1219IUZ | 功能描述:實時時鐘 REAL TIME CLKRTC IN RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| ISL1219IUZ-T | 功能描述:實時時鐘 REAL TIME CLKRTC IN RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| ISL1220 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:I2C㈢ Real Time Clock/Calendar with Frequency Output |
| ISL1220IUZ | 功能描述:實時時鐘 REAL TIME CLKRTC IN RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| ISL1220IUZ-T | 功能描述:實時時鐘 REAL TIME CLKRTC IN RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。