- 您現在的位置：買賣IC網 > PDF目錄1924 > IDT82P20516DBFG (IDT, Integrated Device Technology Inc)IC LIU T1/E1/J1 16CH SH 484BGA PDF資料下載
參數資料
| 型號： | IDT82P20516DBFG |
| 廠商： | IDT, Integrated Device Technology Inc |
| 文件頁數： | 34/115頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC LIU T1/E1/J1 16CH SH 484BGA |
| 標準包裝： | 84 |
| 功能： | 線路接口單元（LIU） |
| 接口： | E1，J1，T1 |
| 電路數： | 16 |
| 電源電壓： | 1.8V, 3.3V |
| 功率（瓦特）： | 2.89W |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 484-LFBGA |
| 供應商設備封裝： | 484-CABGA（19x19） |
| 包裝： | 托盤 |
| 包括： | AIS 警報檢測器和發生器，回送功能，PRBS 發生器 / 檢測器，遠程檢測器和發生器 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁當前第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁
IDT82P20516
16-CHANNEL SHORT HAUL E1 LINE INTERFACE UNIT
Functional Description
25
December 17, 2009
After one of the preset waveform templates is selected, the preset
waveform amplitude can be adjusted to get the desired waveform.
In E1 mode, the SCAL[5:0] bits (b5~0, SCAL,...) should be set to
‘100001’ to get the standard amplitude. The adjusting is made by
increasing or decreasing by ‘1’ from the standard value to scale up or
down at a percentage ratio of 3%.
In summary, do the following step by step, the desired waveform will
be got based on the preset waveform template:
Select one preset waveform template by setting the PULS[3:0] bits
(b3~0, PULS,...);
Write ‘100001 to the SCAL[5:0] bits (b5~0, SCAL,...) if E1 mode is
selected.
Write the scaling value to the SCAL[5:0] bits (b5~0, SCAL,...) to
scale the amplitude of the selected preset waveform template (-
this step is optional).
3.3.4.2 User-Programmable Arbitrary Waveform
When the PULS[3:0] bits (b3~0, PULS,...) are set to ‘1XXX’, user-
programmable arbitrary waveform will be used in the corresponding
channel.
Each waveform shape can extend up to
UIs (Unit Interval), and is
divided into 20 sub-phases that are addressed by the SAMP[4:0] bits
(b4~0, AWG0,...). The waveform amplitude of each phase is repre-
sented by a binary byte, within the range from +63 to -63, stored in the
WDAT[6:0] bits (b6~0, AWG1,...) in signed magnitude form. The
maximum number +63 (D) represents the maximum positive amplitude
of the transmit pulse while the most negative number -63 (D) represents
the maximum negative amplitude of the transmit pulse. Therefore, up to
20 bytes are used.
There are eight standard templates which are stored in a local ROM.
One of them can be selected as reference and made some changes to
get the desired waveform.
To do this, the first step is to choose a set of waveform value from the
standard templates. The selected waveform value should be the most
data of each template.
Then modify the sample data to get the desired transmit waveform
shape. By increasing or decreasing by ‘1’ from the standard value in the
SCAL[5:0] bits (b5~0, SCAL,...), the waveform amplitude will be scaled
up or down.
In summary, do the following for the write operation:
Modify the sample data in the AWG1 register;
Write the AWG0 register to implement the write operation, includ-
ing:
- Write the sample address to the SAMP[4:0] bits (b4~0,
- Write ‘0’ to the RW bit (b5, AWG0,...);
- Write ‘1’ to the DONE bit (b6, AWG0,...).
Do the following for the read operation:
Write the AWG0 register, including:
- Write sample address to the SAMP[4:0] bits (b4~0, AWG0,...);
- Write ‘1’ to the RW bit (b5, AWG0,...);
- Write ‘1’ to the DONE bit (b6, AWG0,...);
Read the AWG1 register to get the sample data.
When the write operation is completed, write the scaling value to the
SCAL[5:0] bits (b5~0, SCAL,...) to scale the amplitude of the selected
standard waveform (- this step is optional).
When more than one UI is used to compose the waveform template
and the waveform amplitude is not set properly, the overlap of the two
consecutive waveforms will make the waveform amplitude overflow (i.e.,
exceed the maximum limitation). This overflow is captured by the
DAC_IS bit (b7, INTS0,...) and will be reported by the INT pin if enabled
by the DAC_IM bit (b7, INTM0,...).
Table-5 PULS[3:0] Setting in E1 Mode
Interface Conditions
PULS[3:0]
E1 75
differential interface,
Internal Impedance matching mode
0000
Other E1 interface
0001
1
4
---
相關PDF資料 |
PDF描述 |
|---|---|
| IDT82P2281PF | TXRX T1/E1/J1 LONG/SHORT 80-TQFP |
| IDT82P2282PF | TXRX T1/J1/E1 2CHAN 100-TQFP |
| IDT82P2284BB | TXRX T1/J1/E1 4CHAN 208-PBGA |
| IDT82P2288BBG | TXRX OCTAL T1/E1/J1 256-PBGA |
| IDT82P2521BHG | IC LIU E1 21+1CH SHORT 640-PBGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IDT82P20516DBFG8 | 制造商:Integrated Device Technology Inc 功能描述:IC LIU T1/E1/J1 16CH SH 484BGA |
| IDT82P20516DBFGBLANK | 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:16-Channel Short Haul E1 Line Interface Unit |
| IDT82P2281 | 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:Single T1/E1/J1 Long Haul Short Haul Transceiver |
| IDT82P2281_09 | 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:Single T1/E1/J1 Long Haul / Short Haul Transceiver |
| IDT82P2281PF | 功能描述:TXRX T1/E1/J1 LONG/SHORT 80-TQFP RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:250 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。