參數資料
型號： HT95C30P
廠商： Holtek Semiconductor Inc.
英文描述： 8-Bit CID Type Phone Controller MCU
中文描述： 8位偵緝型電話MCU控制器
文件頁數： 16/50頁
文件大小： 324K
代理商： HT95C30P
HT95C200/20P/300/30P
Rev. 0.10
16
October 1, 2002
Preliminary
Any reset condition from any operation mode
Any interrupt from Sleep mode or Idle mode
Port A wake-up from Sleep mode or Idle mode
How to change the Operation Mode
Normal mode to Green mode:
ClearMODE1to0,thenoperationmodeischangedto
Green mode but the UPEN status is not changed.
However, UPEN can be cleared by software.
Normal mode or Green mode to Sleep mode:
Step 1: Clear MODE0 to 0
Step 2: Execute HALT instruction
After Step 2, operation mode is changed to Sleep
mode, the UPEN and MODE1 are cleared to 0 by
hardware.
Normal mode or Green mode to Idle mode:
Step 1: Set MODE0 to 1
Step 2: Execute HALT instruction
After Step 2, operation mode is changed to Idle mode,
theUPENandMODE1areclearedto0byhardware.
Green mode to Normal mode:
Step 1: Set UPEN to 1
Step 2: Software delay 20ms at least
Step 3: Set MODE1 to 1
After Step 3, operation mode is changed to Normal
mode.
Sleep mode or Idle mode to Green mode:
Method 1: Any reset condition occurred
Method 2: Any interrupt is active
Method 3: Port A wake-up
Note
The Timer0, Timer1, RTC and dialer I/O inter-
rupt function will not work at the Idle mode be-
cause the 32768Hz crystal is stopped.
Theresetconditionsincludepoweronreset,externalre-
set, WDT time-out reset. By examining the processor
status flag, PD and TO, the program can distinguish be-
tween different reset conditions . Refer to the Reset
function for detailed description.
The port A wake-up and interrupt can be considered as
a continuation of normal execution. Each bit in port A
can be independently selected to wake-up the device by
mask option. Awakening from Port A stimulus, the pro-
gram will resume execution of the next instruction.
Any valid interrupts from Sleep mode or Idle mode may
cause two sequences. One is if the related interrupt is
disabled or the interrupt is enabled but the stack is full,
the program will resume execution at the next instruc-
tion. The other is if the interrupt is enabled and the stack
is not full, the regular interrupt response takes place. It is
necessary to mention that if an interrupt request flag is
set to 1 before entering the Sleep mode or Idle mode,
the wake-up function of the related interrupt will be dis-
abled.
Once a Sleep mode or Idle mode wake-up event occurs,
it will take SST delay time (1024 system clock period) to
resume to Green mode. In other words, a dummy period
is inserted after a wake-up. If the wake-up results from
an interrupt acknowledge signal, the actual interrupt
subroutine execution will be delayed by one or more cy-
cles. If the wake-up results in the next instruction execu-
tion, this will be executed immediately after the dummy
period is finished.
To minimize power consumption, all the I/O pins should
be carefully managed before entering the Sleep mode
or Idle mode.
The Sleep mode or Idle mode is initialized by the HALT
instruction and results in the following.
The system clock will be turned off.
The WDT function will be disabled if the WDT clock
source is the instruction clock.
The WDT function will be disabled if the WDT clock
source is the 32768Hz in Idle mode.
The WDT will still function if the WDT clock source is
the WDT OSC.
If the WDT function is still enabled, the WDT counter
and WDT prescaler will be cleared and recounted
again.
The contents of the on chip RAM and registers remain
unchanged.
All the I/O ports maintain their original status.
The flag PD is set and the flag TO is cleared by hard-
ware.
Reset
There are three ways in which a reset can occur.
Power on reset.
A low pulse onto RES pin.
WDT time-out.
After these reset conditions, the Program Counter and
Stack Pointer will be cleared to 0.
To guarantee that the system oscillator is started and
stabilized, the SST (System Start-up Timer) provides an
extra-delay of 1024 system clock pulses when the sys-
tem is reset or awakes from the Sleep or Idle operation
mode.
>
;
' ' 9
'
<
Reset circuit
相關PDF資料
PDF描述
HT95C200 8-Bit CID Type Phone Controller MCU
HT95CXXX CID Type Phone 8-Bit MCU
HT95L400-128QFP-A LCD Type Phone 8-Bit MCU
HT95L100-64QEP-A LCD Type Phone 8-Bit MCU
HT95L10P-64QEP-A LCD Type Phone 8-Bit MCU
相關代理商/技術參數
參數描述
HT95C400 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:CID Type Phone 8-Bit MCU
HT95C40P 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:LCD Type Phone 8-Bit MCU
HT95CXXX 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:CID Type Phone 8-Bit MCU
HT95L000 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:CID Type Phone 8-Bit MCU
HT95L000-56SSOP-A 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:LCD Type Phone 8-Bit MCU
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*