- 您現在的位置：買賣IC網 > PDF目錄385398 > HT36A4 (Holtek Semiconductor Inc.) 8-Bit Music Synthesizer MCU PDF資料下載
參數資料
| 型號： | HT36A4 |
| 廠商： | Holtek Semiconductor Inc. |
| 英文描述： | 8-Bit Music Synthesizer MCU |
| 中文描述： | 8位微控制器音樂合成器 |
| 文件頁數： | 9/22頁 |
| 文件大小： | 247K |
| 代理商： | HT36A4 |
HT36A4
Rev. 1.00
9
July 2, 2003
Interrupt
The HT36A4 provides two internal Timer Counter inter-
rupts on each bank. The Interrupt Control register
(INTC;0BH) contains the interrupt control bits that sets
the enable/disable and the interrupt request flags.
Once an interrupt subroutine is serviced, all other inter-
rupts will be blocked (by clearing the EMI bit). This
schememaypreventanyfurtherinterruptnesting.Other
interrupt requests may occur during this interval but only
the interrupt request flag is recorded. If a certain inter-
rupt needs servicing within the service routine, the pro-
grammer may set the EMI bit and the corresponding bit
of the INTC to allow interrupt nesting. If the stack is full,
the interrupt request will not be acknowledged, even if
the related interrupt is enabled, until the SP is decre-
mented. If immediate service is desired, the stack must
be prevented from becoming full.
All these kinds of interrupt have a wake-up capability. As
aninterruptisserviced,acontroltransferoccursbypush-
ing the program counter onto the stack and then branch-
ing to subroutines at specified locations in the program
memory. Only the program counter is pushed onto the
stack. If the contents of the register and Status register
(STATUS) are altered by the interrupt service program
whichmaycorruptthedesiredcontrolsequence,thenthe
programmer must save the contents first.
The internal Timer Counter 0 interrupt is initialized by set-
ting the Timer Counter 0 interrupt request flag (T0F; bit 5
of INTC), caused by a Timer Counter 0 overflow. When
the interrupt is enabled, and the stack is not full and the
T0F bit is set, a subroutine call to location 08H will occur.
The related interrupt request flag (T0F) will be reset and
the EMI bit cleared to disable further interrupts.
The Timer Counter 1 interrupt is operated in the same
manner as Timer Counter 0. The related interrupt con-
trol bits ET1I and T1F of the Timer Counter 1 are bit 3
and bit 6 of the INTC respectively.
During the execution of an interrupt subroutine, other in-
terrupt acknowledgments are held until the RETI in-
struction is executed or the EMI bit and the related
interrupt control bit are set to 1 (if the stack is not full). To
return from the interrupt subroutine, the RET or RETI in-
struction may be invoked. RETI will set the EMI bit to en-
able an interrupt service, but RET will not.
Interrupts occurring in the interval between the rising
edges of two consecutive T2 pulses, will be serviced on
the latter of the two T2 pulses, if the corresponding inter-
rupts are enabled. In the case of simultaneous requests
the priorities in the following table apply. These can be
masked by resetting the EMI bit.
Interrupt Source
Priority
Vector
Timer Counter 0 overflow
1
08H
Timer Counter 1 overflow
2
0CH
The Timer Counter 0/1 interrupt request flag (T0F/T1F),
Enable Timer Counter 0/1 bit (ET0I/ET1I), Enable Mas-
ter Interrupt bit (EMI) constitute an interrupt control reg-
ister (INTC) which is located at 0BH in the data memory.
EMI, ET0I, ET1I are used to control the enabling/dis-
abling of interrupts. These bits prevent the requested in-
terrupt from being serviced. Once the interrupt request
flags (T0F, T1F) are set, they will remain in the INTC
register until the interrupts are serviced or cleared by a
software instruction.
It is recommended that a program does not use the
CALL subroutine within the interrupt subroutine. Be-
cause interrupts often occur in an unpredictable manner
or need to be serviced immediately in some applica-
tions, if only one stack is left and enabling the interrupt is
not well controlled, once the CALLsubroutine operates
in the interrupt subroutine, it may damage the original
control sequence.
Labels
Bits
Function
C
0
C is set if an operation results in a carry during an addition operation or if a borrow does not take
place during a subtraction operation; otherwise C is cleared. Also it is affected by a rotate
through carry instruction.
AC
1
AC is set if an operation results in a carry out of the low nibbles in addition or no borrow from the
high nibble into the low nibble in subtraction; otherwise AC is cleared.
Z
2
Z is set if the result of an arithmetic or logical operation is zero; otherwise Z is cleared.
OV
3
OV is set if an operation results in a carry into the highest-order bit but not a carry out of the high-
est-order bit, or vice versa; otherwise OV is cleared.
PD
4
PD is cleared by either a system power-up or executing the CLR WDT instruction. PD is set by
executing the HALT instruction.
TO
5
TOisclearedbyasystempower-uporexecutingtheCLRWDTorHALTinstruction.TOissetby
a WDT time-out.
6~7
Unused bit, read as 0
Status register
相關PDF資料 |
PDF描述 |
|---|---|
| HT3810 | 128 NOTE MELODY GENERATORS |
| HT3810A | 128 NOTE MELODY GENERATORS |
| HT3810B | 128 NOTE MELODY GENERATORS |
| HT3810C | 128 NOTE MELODY GENERATORS |
| HT3810D | 128 NOTE MELODY GENERATORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HT36A4_07 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:Music Synthesizer 8-Bit MCU |
| HT36ARP | 功能描述:兩端交流開關元件 32-40V RoHS:否 制造商:STMicroelectronics 轉折電流 VBO:45 V 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23 封裝:Reel |
| HT36B | 功能描述:兩端交流開關元件 34-38V RoHS:否 制造商:STMicroelectronics 轉折電流 VBO:45 V 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23 封裝:Reel |
| HT-36B | 制造商:TECCOR 制造商全稱:TECCOR 功能描述:Bilateral Trigger Diacs |
| HT36B0 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:8-Bit Music Synthesizer MCU |
發布緊急采購，3分鐘左右您將得到回復。