參數資料
型號： HMP8156A
廠商： Intersil Corporation
英文描述： NTSC/PAL Encoders
中文描述： 的NTSC / PAL編碼器
文件頁數： 31/34頁
文件大?。?/td> 256K
代理商： HMP8156A
31
Application Information
Vertical Blanking Information Encoding
VBI data such as teletext may be encoded on any line by
driving the pixel inputs with appropriate data. For YCbCr
input modes, Cb and Cr should equal 128 to disable the
color information. For RGB input modes, R, G, and B should
always have the same value to disable the color information.
Vertical blanking must be negated on the first scan line
containing VBI information. If there are unused scan lines
between the VBI data and active video, BLANK must remain
on and the pixel inputs should be set to the black level.
Video Insertion Test Signalsy
Video test signals may be generated by driving the pixel
inputs with appropriate data. Most of the video test signals
require using YCbCr pixel data.
Vertical blanking must be negated on the first scan line
containing video test signals. If there are unused scan lines
between test signal data and active video, BLANK must
remain off and the pixel inputs should be set to the black level.
PCB Considerations
A PCB board with a minimum of 4 layers is recommended, with
layers 1 and 4 (top and bottom) for signals and layers 2 and 3
for power and ground. The PCB layout should implement the
lowest possible noise on the power and ground planes by
providing excellent decoupling. PCB trace lengths between
groups of V
AA
and GND pins should be as short as possible.
Component Placement
The optimum layout places the HMP8154/HMP8156A at the
edge of the PCB and as close as possible to the video output
connector. External components should be positioned as
close as possible to the appropriate pin, ideally such that
traces can be connected point to point. Chip capacitors are
recommended where possible, with radial lead ceramic
capacitors the second-best choice.
Traces containing digital signals should not be routed over,
under, or adjacent to the analog output traces to minimize
crosstalk. If this is not possible, coupling can be minimized
by routing the digital signals at a 90 degree angle to the ana-
log signals. The analog output traces should also not cross
over or under the V
CC
power plane to maximize high-fre-
quency power supply rejection.
Power and Ground Planes
A common ground plane for all devices, including the
HMP8154/HMP8156A, is recommended. However, placing the
encoder on an electrically connected GND peninsula reduces
noise levels. All GND pins on the HMP8154/HMP8156A must
be connected to the ground plane. Typical power and ground
planes are shown in Figure 36.
The small connection between the ground areas should be
made wide enough so that most of the encoders digital inputs
can be routed over or under it. It is especially important that the
CLK and CLK2 signals cross through the connection.
The HMP8154/HMP8156A should have its own power plane
that is isolated from the common power plane of the board,
with a gap between the two power planes of at least 1/8 inch.
All V
AA
pins of the HMP8154/HMP8156A must be
connected to this isolated power plane.
The HMP8154/HMP8156A power plane should be connected
to the board’s normal V
CC
power plane at a single point though
a low-resistance ferrite bead, such as a Ferroxcube 5659065-
3B, Fair-Rite 2743001111, or TDK BF45-4001. The ferrite bead
provides resistance to switching currents, improving the
performance of HMP8154/HMP8156A. A single, large
capacitor should also be used between the
HMP8154/HMP8156A power plane and the ground plane to
control low-frequency power supply ripple.
FIGURE 34. H SYNC JITTER IN A FRAME (PAL)
FIGURE 35. SCH PHASE MEASUREMENT (PAL)
Typical Performance Curves
(Continued)
HMP8154, HMP8156A
相關PDF資料
PDF描述
HMP8154EVAL1 NTSC/PAL Encoders
HMP8190 NTSC/PAL Video Encoder
HMP8190CN NTSC/PAL Video Encoder
HMP8190EVAL1 NTSC/PAL Video Encoder
HMP8191 NTSC/PAL Video Encoder
相關代理商/技術參數
參數描述
HMP8156ACN 功能描述:編碼器、解碼器、復用器和解復用器 64MQFP,0+70C NTSC/PAL VIDEO ENCODER RoHS:否 制造商:Micrel 產品:Multiplexers 邏輯系列:CMOS 位數: 線路數量（輸入/輸出）:2 / 12 傳播延遲時間:350 ps, 400 ps 電源電壓-最大:2.625 V, 3.6 V 電源電壓-最小:2.375 V, 3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Tray
HMP8156ACNZ 功能描述:編碼器、解碼器、復用器和解復用器 W/ANNEAL 64MQFP 0+70 ENCODER RoHS:否 制造商:Micrel 產品:Multiplexers 邏輯系列:CMOS 位數: 線路數量（輸入/輸出）:2 / 12 傳播延遲時間:350 ps, 400 ps 電源電壓-最大:2.625 V, 3.6 V 電源電壓-最小:2.375 V, 3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Tray
HMP8156CN 制造商:Rochester Electronics LLC 功能描述:- Bulk
HMP8156EVAL1 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:NTSC/PAL Encoders
HMP8156EVAL2 制造商:Rochester Electronics LLC 功能描述:- Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*