- 您現在的位置：買賣IC網 > PDF目錄370471 > HD66705U (Hitachi,Ltd.) Low-Power Dot-Matrix Liquid Crystal Display Controller/Driver(圖形LCD控制器/驅動器) PDF資料下載
參數資料
| 型號： | HD66705U |
| 廠商： | Hitachi,Ltd. |
| 英文描述： | Low-Power Dot-Matrix Liquid Crystal Display Controller/Driver(圖形LCD控制器/驅動器) |
| 中文描述： | 低功耗點陣液晶顯示控制器/驅動器（圖形液晶顯示控制器/驅動器） |
| 文件頁數： | 68/81頁 |
| 文件大小： | 426K |
| 代理商： | HD66705U |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁當前第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁
HD66705U
68
Standby Mode
Setting the standby mode bit (STB) to 1 puts the
HD66705U
in standby mode, where the device stops
completely, halting all internal operations including the R-C oscillator, thus further reducing current
consumption compared to that in sleep mode. Specifically, character and segment displays, which are
controlled by the multiplexing drive method, are completely halted. Here, all the SEG (SEG1 to SEG60)
and COM (COM1 to COM16, COMS1/2) pins output the V
CC
level, resulting in no display. If the AMP bit
is set to 0 in standby mode, the LCD drive power supply can be turned off.
Annunciators can be displayed simply by supplying an approximately 40-Hz alternating signal for the LCD
drive signals to the EXM pin externally. If annunciator display is unnecessary during standby mode, the
EXM pin must be fixed to the V
CC
or GND level and the annunciator display-on bit (DA) set to 0.
During standby mode, no instructions can be accepted other than those for annunciator display and the
start-oscillator instruction. To cancel standby mode, issue the start-oscillator instruction to stabilize R-C
oscillation before setting the STB bit to 0.
Figure 45 shows the procedure for setting and cancelling standby mode.
Turn off the LCD power supply: AMP = 0
Only for annunciator display;
set the DA bit to 0 when
annunciator display is not necessary.
Set standby mode: STB = 1
Supply an external alternating signal to the EXM pin
Issue the start-oscillator instruction
Wait at least 10 ms
Cancel standby mode: STB = 0
Turn on the LCD drive power supply: AMP = 1
Standby mode (only annunciator display is available)
Figure 45 Procedure for Setting and Cancelling Standby Mode
相關PDF資料 |
PDF描述 |
|---|---|
| HD66710 | (Dot Matrix Liquid Crystal Display Controller/Driver) |
| HD66710A00FS | 16 AMP SPDT MINIATURE POWER RELAY |
| HD66710A00TF | (Dot Matrix Liquid Crystal Display Controller/Driver) |
| HD66712U | Dot-Matrix Liquid Crystal Display Controller/Driver(點陣液晶顯示控制器/驅動器) |
| HD66712 | Dot-Matrix Liquid Crystal Display Controller/Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HD66710 | 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:(Dot Matrix Liquid Crystal Display Controller/Driver) |
| HD66710A00FS | 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:(Dot Matrix Liquid Crystal Display Controller/Driver) |
| HD66710A00TF | 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:(Dot Matrix Liquid Crystal Display Controller/Driver) |
| HD66712 | 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:Dot-Matrix Liquid Crystal Display Controller/Driver |
| HD66712A00TA0 | 制造商:Renesas Electronics Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。