- 您現在的位置：買賣IC網 > PDF目錄1922 > FT2232D-REEL (FTDI, Future Technology Devices International Ltd)IC USB FS DUAL UART/FIFO 48-LQFP PDF資料下載
參數資料
| 型號： | FT2232D-REEL |
| 廠商： | FTDI, Future Technology Devices International Ltd |
| 文件頁數： | 18/61頁 |
| 文件大小： | 0K |
| 描述： | IC USB FS DUAL UART/FIFO 48-LQFP |
| 產品培訓模塊： | USB Introduction |
| 標準包裝： | 1 |
| 系列： | USBmadeEZ-FIFO，F(xiàn)T-X，X-Chip |
| 特點： | USB 至 UART 和（或）FIFO、SPI、I2C、JTAG |
| 通道數： | 2，DUART |
| FIFO's： | 384 字節 |
| 規程： | RS232，RS422，RS485 |
| 電源電壓： | 4.35 V ~ 5.25 V |
| 帶并行端口： | 是 |
| 帶自動流量控制功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-LQFP |
| 供應商設備封裝： | 48-LQFP |
| 包裝： | 標準包裝 |
| 產品目錄頁面： | 634 (CN2011-ZH PDF) |
| 配用： | 768-1030-ND - MOD USB HS FT2232H EVAL 813-1009-ND - MODULE USB-TO-FPGA TOOL W/MANUAL 813-1001-ND - MODULE USB ADAPTR FOR FT2232D LP 813-1000-ND - MODULE USB ADAPTER FOR FT2232D |
| 其它名稱： | 768-1010-6 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁
Copyright 2010 Future Technology Devices International Limited
25
Document No.: FT_000173
FT2232D DUAL USB TO SERIAL UART
/FIFO IC Datasheet
Version 2.05
Clearance No.: FTDI# 127
6.3 Power Switching Configuration
Figure 6.5 Bus Powered Circuit with Power Control
USB Bus powered circuits need to be able to power down in USB suspend mode in order to meet
the <= 500μA total suspend current requirement (including external logic). Some external logic can
power itself down into a low current state by monitoring the PWREN# pin. For external logic that
cannot power itself down in that way, the FT2232D provides a simple but effective way of turning
off power to external circuitry during USB suspend.
Figure 6.5 shows how to use a discrete P-Channel Logic Level MOSFET to control the power to
external logic circuits. A suitable device would be an International Rectifier (www.irf.com)
IRLML6402, or equivalent. It is recommended that a “soft start” circuit consisting of a 1K series
resistor and a 0.1 μF capacitor are used to limit the current surge when the MOSFET turns on.
Without the soft start circuit there is a danger that the transient power surge of the MOSFET turning
on will reset the FT2232D, or the USB host / hub controller. The values used here allow attached
circuitry to power up with a slew rate of ~12.5 V per millisecond, in other words the output voltage
will transition from GND to 5V in approximately 400 microseconds.
Alternatively, a dedicated power switches I.C. with inbuilt “soft-start” can be used instead of a
MOSFET. A suitable power switch I.C. for such an application would be a Micrel (www.micrel.com)
MIC2025-2BM or equivalent. Please note the following points in connection with power controlled
designs: –
a)The logic to be controlled must have its own reset circuitry so that it will automatically reset
itself when power is re-applied on coming out of suspend.
b)Set the Pull-down on Suspend option in the FT2232Ds EEPROM.
c)For USB high-power bus powered device (one that consumes greater than 100 mA, and up to
500 mA of current from the USB bus), the power consumption of the device should be set in the
max power field in the EEPROM. A high-power bus powered device must use this descriptor in the
EEPROM to inform the system of its power requirements.
d)For 3.3V power controlled circuits the VCCIO pins must not be powered down with the external
circuitry. Either connect the power switch between the output of the 3.3V regulator and the
external 3.3V logic, or if appropriate power the VCCIO pin from the 3V3OUT pin of the FT2232D.
相關PDF資料 |
PDF描述 |
|---|---|
| FT2232HQ-REEL | IC USB HS DUAL UART/FIFO 64-QFN |
| FT232BL-REEL | IC USB FS SERIAL UART 32-LQFP |
| FT232HL-REEL | IC HS USB TO UART/FIFO 48LQFP |
| FT232RL-REEL | IC USB FS SERIAL UART 28-SSOP |
| FT245BL-REEL | IC USB FS PARALLEL FIFO 32-LQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FT2232D-TRAY | 制造商:Future Technology Devices International (FTDI Chip) 功能描述:DUAL USB TO SERIAL UART/FIFO IC |
| FT2232H | 制造商:FTDI 制造商全稱:FTDI 功能描述:DUAL HIGH SPEED USB TO MULTIPURPOSE UART |
| FT2232H MINI MODULE | 功能描述:界面開發工具 USB Hi-Speed FT2232H Evaluation Module RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| FT2232H_10 | 制造商:FTDI 制造商全稱:FTDI 功能描述:DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC |
| FT2232H_12 | 制造商:FTDI 制造商全稱:FTDI 功能描述:Dual High Speed USB to Multipurpose UART/FIFO IC |
發布緊急采購，3分鐘左右您將得到回復。