- 您現在的位置：買賣IC網 > PDF目錄375725 > FAN53180 (Fairchild Semiconductor Corporation) 6-Bit VID Controlled 2-4 Phase DC-DC Controller PDF資料下載
參數資料
| 型號： | FAN53180 |
| 廠商： | Fairchild Semiconductor Corporation |
| 英文描述： | 6-Bit VID Controlled 2-4 Phase DC-DC Controller |
| 中文描述： | 6位VID控制2-4相DC - DC控制器 |
| 文件頁數： | 24/28頁 |
| 文件大?。?/td> | 851K |
| 代理商： | FAN53180 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁
FAN53180
PRODUCT SPECIFICATION
24
REV. 1.0.0 6/10/03
Figure 8. AC Loadline Waveform
16. If the V
ACDRP
and V
DCDRP
are different by more than
a couple of millivolts, use Equation 38 to adjust C
CS
.
You may need to parallel different values to get the right
one since there are limited standard capacitor values
available (it is a good idea to have locations for two
capacitors in the layout for this).
17. Repeat Steps 11 to 13 and repeat adjustments if neces-
sary. Once complete, do not change C
CS
for the rest of
the procedure.
18. Set dynamic load step to maximum step size (do not use
a step size larger than needed) and verify that the output
waveform is square (which means V
ACDRP and
V
DCDRP
are equal). NOTE: MAKE SURE LOAD STEP SLEW
RATE AND TURN-ON ARE SET FOR A SLEW RATE
OF ~150–250A/μs (for example, a load step of 50A
should take 200 ns–300 ns) WITH NO OVERSHOOT.
Some dynamic loads will have an excessive turn-on
overshoot if a minimum current is not set properly (this
is an issue if using a VTT tool).
Initial Transient Setting
19. With dynamic load still set at maximum step size,
expand scope time scale to see 2μs/div to 5μs/div. You
will see a waveform that may have two overshoots and
one minor undershoot (see Figure 9). Here, V
DROOP
is
the final desired value.
Figure 9. Transient Setting Waveform
20. If both overshoots are larger than desired, try making the
following adjustments in this order. (NOTE: If these
adjustments do not change the response, you are limited
by the output decoupling.) Check the output response
each time you make a change as well as the switching
nodes (to make sure it is still stable).
a. Make ramp resistor larger by 25% (R
RAMP
).
b. For V
TRAN1
, increase C
B
or increase switching
frequency.
c. For V
TRAN2
, increase R
A
and decrease C
A
by 25%.
21. For load release (see Figure 10), if V
TRANREL
is larger
than V
TRAN1
(see Figure 9), you do not have enough
output capacitance. You will either need more capaci-
tance or to make the inductor values smaller (if you
change inductors, you need to start the design over using
the spreadsheet and this tuning procedure).
Figure 10. Transient Setting Waveform
C
CS NEW
)
C
CS OLD
)
V
DCDRP
---------------------
×
=
(38)
相關PDF資料 |
PDF描述 |
|---|---|
| FAN5330 | High Efficiency Serial LED Driver with 30V Integrated Switch |
| FAN5331 | 1.6MHz Boost Converter with 20V Integrated FET Switch |
| FAN5331SX | 1.6MHz Boost Converter with 20V Integrated FET Switch |
| FAN5332A | High Efficiency, High Current Serial LED Driver and OLED Supply with 30V Integrated Switch |
| FAN5332ASX | High Efficiency, High Current Serial LED Driver and OLED Supply with 30V Integrated Switch |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FAN53180MTC | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:6-Bit VID Controlled 2-4 Phase DC-DC Controller |
| FAN53180MTCX | 功能描述:DC/DC 開關控制器 Buck Controller 2to4 Phs VID Sync RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| FAN5330 | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:High Efficiency Serial LED Driver with 30V Integrated Switch |
| FAN5330SX | 功能描述:LED照明驅動器 SYSTEM_POWER RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| FAN5331 | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:High Efficiency Serial LED Driver and OLED Supply with 20V Integrated Switch |
發布緊急采購，3分鐘左右您將得到回復。