- 您現在的位置：買賣IC網 > PDF目錄17109 > EVAL-ADUC7124QSPZ (Analog Devices Inc)BOARD EVALUATION FOR ADUC7124 PDF資料下載
參數資料
| 型號： | EVAL-ADUC7124QSPZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 100/108頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVALUATION FOR ADUC7124 |
| 設計資源： | EVAL-ADUC7124 Schematic ADUC7124 Eval Brd Gerber Files |
| 標準包裝： | 1 |
| 系列： | MicroConverter® ADuC7xxx |
| 類型： | MCU |
| 適用于相關產品： | ADUC7124 |
| 所含物品： | 板 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁當前第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁
Data Sheet
ADuC7124/ADuC7126
Rev. C | Page 91 of 108
TIMERS
The ADuC7124/ADuC7126 have four general-purpose
timers/counters.
Timer0
Timer1
Timer2 or wake-up timer
Timer3 or watchdog timer
These four timers in their normal mode of operation can be
either free running or periodic.
In free-running mode, the counter decreases from the maxi-
mum value until zero scale is reached and starts again at the
minimum value. It also increases from the minimum value until
full scale is reached and starts again at the maximum value.
In periodic mode, the counter decrements/increments from the
value in the load register (TxLD MMR) until zero/full scale is
reached and starts again at the value stored in the load register.
The timer interval is calculated as follows:
If the timer is set to count down, then
(
)
Clock
Source
Prescaler
TxLD
Interval
×
=
If the timer is set to count up, then
(
)
Clock
Source
Prescaler
TxLD
FullScale
Interval
×
=
-
The value of a counter can be read at any time by accessing
its value register (TxVAL). Note that, when a timer is being
clocked from a clock other than a core clock, an incorrect
value may be read (due to asynchronous clock system). In this
configuration, TxVAL should always be read twice. If the two
readings are different, it should be read a third time to obtain
the correct value.
Timers are started by writing in the control register of the
corresponding timer (TxCON).
In normal mode, an IRQ is generated each time the value of the
counter reaches zero when counting down. It is also generated
each time the counter value reaches full scale when counting
up. An IRQ can be cleared by writing any value to clear the
register of that particular timer (TxCLRI).
When using an asynchronous clock-to-clock timer, the
interrupt in the timer block can take more time to clear
than the time it takes for the code in the interrupt routine to
execute. Ensure that the interrupt signal is cleared before
leaving the interrupt service routine. This can be done by
checking the IRQSTA MMR.
Hr: Min: Sec: 1/128 Format
Timer 1 and Timer 2 have an Hr: Min: Sec: hundreds format.
To use the timer in Hr: Min: Sec: hundreds format, the
32768 kHz clock and prescaler of 256 should be selected. The
hundreds field does not represent milliseconds, but 1/128 of a
second (256/32768).The bits representing the hour, minute,
and second are not consecutive in the register. This arrange-
ment applies to TxLD and TxVAL when using the Hr: Min: Sec:
hundreds format as set in TxCON[5:4]. See Table 140 for more
details.
Table 140. Hr: Min: Sec: Hundreds Format
Bit
Value
Description
[31:24]
0 to 23 or 0 to 255
hours
[23:22]
0
reserved
[21:16]
0 to 59
minutes
[15:14]
0
reserved
[13:8]
0 to 59
seconds
7
0
reserved
[6:0]
0 to 127
1/128 of second
相關PDF資料 |
PDF描述 |
|---|---|
| ECM30DCWN | CONN EDGECARD 60POS DIP .156 SLD |
| EVAL-ADUC7121QSPZ | BOARD EVALUATION FOR ADUC7121 |
| EVAL-ADUC7126QSPZ | BOARD EVALUATION FOR ADUC7126 |
| REC5-243.3SRWZ/H4/A | CONV DC/DC 5W 9-36VIN 3.3VOUT |
| EVAL-ADUC7023QSPZ | KIT DEV FOR ADUC7023 QUICK START |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-ADUC7126QSPZ | 功能描述:BOARD EVALUATION FOR ADUC7126 RoHS:是 類別:編程器，開發系統 >> 通用嵌入式開發板和套件（MCU、DSP、FPGA、CPLD等） 系列:MicroConverter® ADuC7xxx 標準包裝:1 系列:PICDEM™ 類型:MCU 適用于相關產品:PIC10F206，PIC16F690，PIC16F819 所含物品:板，線纜，元件，CD，PICkit 編程器 產品目錄頁面:659 (CN2011-ZH PDF) |
| EVAL-ADUC7128QSPZ | 功能描述:KIT DEV FOR ADUC7128 RoHS:是 類別:編程器，開發系統 >> 通用嵌入式開發板和套件（MCU、DSP、FPGA、CPLD等） 系列:QuickStart™ PLUS 套件 產品培訓模塊:Blackfin® Processor Core Architecture Overview Blackfin® Device Drivers Blackfin® Optimizations for Performance and Power Consumption Blackfin® System Services 特色產品:Blackfin? BF50x Series Processors 標準包裝:1 系列:Blackfin® 類型:DSP 適用于相關產品:ADSP-BF548 所含物品:板，軟件，4x4 鍵盤，光學撥輪，QVGA 觸摸屏 LCD 和 40G 硬盤 配用:ADZS-BFBLUET-EZEXT-ND - EZ-EXTENDER DAUGHTERBOARDADZS-BFLLCD-EZEXT-ND - BOARD EXT LANDSCAP LCD INTERFACE 相關產品:ADSP-BF542BBCZ-4A-ND - IC DSP 16BIT 400MHZ 400CSBGAADSP-BF544MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542KBCZ-6A-ND - IC DSP 16BIT 600MHZ 400CSBGAADSP-BF547MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF548BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF547BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF544BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF542BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGA |
| EVAL-ADUC7128QSPZ2 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Precision Analog Microcontroller ARM7TDMI MCU with 12-Bit ADC and DDS DAC |
| EVAL-ADUC7129QSPZ | 制造商:Analog Devices 功能描述:- Bulk |
| EVAL-ADUC812QS | 制造商:Analog Devices 功能描述:DEVELOPMENT KIT SYSTEM |
發布緊急采購，3分鐘左右您將得到回復。