V
參數資料
型號： EVAL-AD7291SDZ
廠商： Analog Devices Inc
文件頁數： 28/29頁
文件大小： 0K
描述： BOARD EVAL FOR AD7291
標準包裝： 1
ADC 的數量： 8
位數： 12
采樣率（每秒）： 22.22k
數據接口： I²C
已用 IC / 零件： AD7291
已供物品： 板
相關產品： AD7291BCPZ-RL7-ND - IC ADC I2C/SRL 22.22K 20LFCSP
AD7291BCPZ-ND - IC ADC 12BIT SAR 8CH 20-LFCSP
Data Sheet
AD7291
Rev. B | Page 7 of 28
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
14
13
12
1
3
4
SDA
15
SCL
AS1
ALERT
11
AS0
VIN3
VIN5
2
VIN4
VIN6
5
VIN7
7
V
R
E
F
6
G
N
D
1
8
D
C
A
P
9
G
N
D
1
0
V
D
1
9
V
IN
1
2
0
V
IN
2
1
8
V
IN
0
1
7
P
D
/R
S
T
1
6
V
D
R
IV
E
AD7291
TOP VIEW
(Not to Scale)
08
7
1
1-
0
03
NOTES
1. THE EXPOSED METAL PADDLE ON THE BOTTOM
OF THE LFCSP PACKAGE SHOULD BE SOLDERED
TO PCB GROUND FOR PROPER HEAT DISSIPATION
AND PERFORMANCE.
Figure 3. Pin Configuration
Table 6. Pin Function Descriptions
Pin No.
Mnemonic
Description
1 to 5,
18 to 20
VIN3, VIN4,
VIN5, VIN6,
VIN7, VIN0,
VIN1, VIN2
Analog Inputs. The AD7291 has eight single-ended analog inputs that are multiplexed into the on-chip track-and-
hold amplifier. Each input channel can accept analog inputs from 0 V to 2.5 V. Any unused input channels should
be connected to GND1 to avoid noise pickup.
6
GND1
Ground. Ground reference point for the internal reference circuitry on the AD7291. All analog input signals and
the external reference signals should be referred to this GND1 voltage. The GND1 pin should be connected to the
ground plane of a system. All ground pins should ideally be at the same potential and must not be more than 0.3 V
apart, even on a transient basis. The VREF pin should be decoupled to this ground pin via a 10 μF decoupling
capacitor.
7
VREF
Internal Reference/External Reference Supply. The nominal internal reference voltage of 2.5 V appears at this pin.
Provided the output is buffered, the on-chip reference can be taken from this pin and applied externally to the rest
of a system. Decoupling capacitors should be connected to this pin to decouple the reference buffer. For best
performance, it is recommended to use a 10 μF decoupling capacitor on this pin to GND1. The internal reference
can be disabled and an external reference supplied to this pin if required. The input voltage range for the external
reference is 2.0 V to 2.5 V.
8
DCAP
Decoupling Capacitor Pin. Decoupling capacitors (1 μF recommended) are connected to this pin to decouple the
internal LDO.
9
GND
Ground. Ground reference point for all analog and digital circuitry on the AD7291. The GND pin should be con-
nected to the ground plane of the system. All ground pins should ideally be at the same potential and must not be
more than 0.3 V apart, even on a transient basis. Both DCAP and VDD pins should be decoupled to this GND pin.
10
VDD
Supply Voltage, 2.8 V to 3.6 V. This supply should be decoupled to GND with 10 μF and 100 nF decoupling capacitors.
11, 13
AS0, AS1
Logic Input. Together, the logic state of these two inputs selects a unique I2C address for the AD7291. See Table 31
for details. The device address depends on the voltage applied to these pins.
12
ALERT
Digital Output. This pin acts as an out-of-range indicator and, if enabled, becomes active when the conversion
result violates the DATAHIGH or DATALOW register values. See the Limit Registers (0x04 to 0x1E) section.
14
SDA
Digital Input/Output. Serial bus bidirectional data. This open-drain output requires a pull-up resistor. The output coding
is straight binary for the voltage channels and twos complement for the temperature sensor result.
15
SCL
Digital Input. Serial I2C Bus Clock. This input requires a pull-up resistor. The data transfer rate in I2C mode is
compatible with both 100 kHz and 400 kHz operating modes.
16
VDRIVE
Logic Power Supply Input. The voltage supplied at this pin determines the voltage at which the interface operates.
This pin should be decoupled to GND. The voltage range on this pin is 1.65 V to 3.6 V and may be less than the
voltage at VDD but should never exceed it by more than 0.3 V.
17
PD/RST
Power-Down Pin. This pin places the part into a full power-down mode and enables power conservation when
operation is not required. This pin can be used to reset the device by toggling the pin low for a minimum of 1 ns and a
maximum of 100 ns. If the maximum time is exceeded, the part enters power-down mode. When placing the device in
full power-down mode, the analog inputs must be returned to 0 V.
EPAD
Exposed Paddle. The exposed metal paddle on the bottom of the LFCSP package should be soldered to PCB
ground for proper functionality and heat dissipation.
相關PDF資料
PDF描述
MIC2562A-1YTS IC PCMCIA/CARDBUS CTRLR 16-TSSOP
EEM30DRSN CONN EDGECARD 60POS DIP .156 SLD
EVAL-AD7192EBZ BOARD EVAL FOR AD7192
LQH3NPN220MJ0L INDUCTOR POWER 22UH 510MA 1212
PCMC063T-R68MN COIL .68UH POWER CHOKE 20% SMD
相關代理商/技術參數
參數描述
EVAL-AD7292SDZ 功能描述:數據轉換 IC 開發工具 EVALUATION BOARD RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V
EVAL-AD7294EBZ 功能描述:BOARD EVALUATION FOR AD7294 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件
EVAL-AD7298SDZ 功能描述:BOARD EVAL FOR AD7298 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件
EVAL-AD7298SDZ 制造商:Analog Devices 功能描述:EVAL BOARD, AD7192 12BIT ADC
EVAL-AD7321CB 制造商:AD 制造商全稱:Analog Devices 功能描述:500 kSPS, 2-Channel, Software-Selectable, True Bipolar Input, 12-Bit Plus Sign ADC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*