參數資料
型號: DSP56303AG100B1
廠商: Freescale Semiconductor
文件頁數: 18/108頁
文件大小: 0K
描述: IC DSP 24BIT 100MHZ 144-LQFP
標準包裝: 300
系列: DSP563xx
類型: 定點
接口: 主機接口,SSI,SCI
時鐘速率: 100MHz
非易失內存: ROM(576 B)
芯片上RAM: 24kB
電壓 - 輸入/輸出: 3.30V
電壓 - 核心: 3.30V
工作溫度: -40°C ~ 100°C
安裝類型: 表面貼裝
封裝/外殼: 144-LQFP
供應商設備封裝: 144-LQFP(20x20)
包裝: 托盤
Enhanced Synchronous Serial Interface 1 (ESSI1)
DSP56303 Technical Data, Rev. 11
Freescale Semiconductor
1-13
SCK1
PD3
Input/Output
Input or Output
Ignored Input
Serial Clock—Provides the serial bit rate clock for the ESSI. The SCK1 is a
clock input or output used by both the transmitter and receiver in synchronous
modes or by the transmitter in asynchronous modes.
Although an external serial clock can be independent of and asynchronous to
the DSP system clock, it must exceed the minimum clock cycle time of 6T (that
is, the system clock frequency must be at least three times the external ESSI
clock frequency). The ESSI needs at least three DSP phases inside each half of
the serial clock.
Port D 3—The default configuration following reset is GPIO input PD3. When
configured as PD3, signal direction is controlled through the Port D Direction
Register. The signal can be configured as an ESSI signal SCK1 through the Port
D Control Register.
SRD1
PD4
Input
Input or Output
Ignored Input
Serial Receive Data—Receives serial data and transfers the data to the ESSI
Receive Shift Register. SRD1 is an input when data is being received.
Port D 4—The default configuration following reset is GPIO input PD4. When
configured as PD4, signal direction is controlled through the Port D Direction
Register. The signal can be configured as an ESSI signal SRD1 through the
Port D Control Register.
STD1
PD5
Output
Input or Output
Ignored Input
Serial Transmit Data—Transmits data from the Serial Transmit Shift Register.
STD1 is an output when data is being transmitted.
Port D 5—The default configuration following reset is GPIO input PD5. When
configured as PD5, signal direction is controlled through the Port D Direction
Register. The signal can be configured as an ESSI signal STD1 through the Port
D Control Register.
Notes:
1.
In the Stop state, the signal maintains the last state as follows:
If the last state is input, the signal is an ignored input.
If the last state is output, the signal is tri-stated.
2.
The Wait processing state does not affect the signal state.
3.
All inputs are 5 V tolerant.
Table 1-13.
Enhanced Serial Synchronous Interface 1 (Continued)
Signal Name
Type
State During
Reset1,2
Signal Description
相關PDF資料
PDF描述
KMSC7119VF1200 DSP 16BIT W/DDR CTRLR 400-MAPBGA
VI-21P-EU CONVERTER MOD DC/DC 13.8V 200W
VI-21N-EU CONVERTER MOD DC/DC 18.5V 200W
KMSC7119VM1200 DSP 16BIT W/DDR CTRLR 400-MAPBGA
KMSC7118VF1200 DSP 16BIT W/DDR CTRLR 400-MAPBGA
相關代理商/技術參數
參數描述
DSP56303AG100R2 功能描述:數字信號處理器和控制器 - DSP, DSC 24 BIT DSP RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
DSP56303EVM 功能描述:數字信號處理器和控制器 - DSP, DSC DSP56303 Eval Kit RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
DSP56303EVMCL 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DSP56303EVM DSP56303EVM Kit Contents List
DSP56303EVMUM 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DSP56303 EVM Users Manual
DSP56303PV100 制造商:Freescale Semiconductor 功能描述:Digital Signal Processor, 24 Bit, 144 Pin, Plastic, QFP