- 您現在的位置：買賣IC網 > PDF目錄97857 > DS1077Z-66 (DALLAS SEMICONDUCTOR) 66.666 MHz, OTHER CLOCK GENERATOR, PDSO8 PDF資料下載
參數資料
| 型號： | DS1077Z-66 |
| 廠商： | DALLAS SEMICONDUCTOR |
| 元件分類： | Clock Generator |
| 英文描述： | 66.666 MHz, OTHER CLOCK GENERATOR, PDSO8 |
| 封裝： | 0.150 INCH, SOIC-8 |
| 文件頁數： | 15/17頁 |
| 文件大?。?/td> | 103K |
| 代理商： | DS1077Z-66 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁
DS1077
7 of 17
(Refer to Table 5)
Table 5
Bit Value
Divisor (N)
0 000 000 000
**
2
0 000 000 001
3
--
1 111 111 111
1025
**Default Condition
BUS WORD
Name
---
B
WC
A2
A1
A0
Factory Default
0*0*0*0*
0
*These bits are reserved and must be set to “0” zero
A0,A1,A2
(Default Setting = 000)
These are the device select bits which determine the address of the device.
WC
(Default Setting WC=0)
This bit determines when/if the EEPROM is written to after register contents have been changed.
If WC = 0 the EEPROM is written automatically after a write register command.
If WC = 1 the EEPROM is only written when the “WRITE ” command is issued.
Regardless of the value of the WC bit the value of the BUS Register (A0,A1,A2) is always written
immediately to the EEPROM.
2-WIRE SERIAL DATA BUS
The DS1077 supports a bi-directional two-wire bus and data transmission protocol. A device that sends
data onto the bus is defined as a transmitter, and a device receiving data as a receiver. The device that
controls the message is called a "master". The devices that are controlled by the master are "slaves". The
bus must be controlled by a master device which generates the serial clock (SCL), controls the bus access,
and generates the START and STOP conditions. The DS1077 operates as a slave on the two-wire bus.
Connections to the bus are made via the open-drain I/O lines SDA* and SCL. A pullup resistor (5K) is
connected to SDA
The following bus protocol has been defined (See Figure 2):
Data transfer may be initiated only when the bus is not busy.
During data transfer, the data line must remain stable whenever the clock line is HIGH. Changes
in the data line while the clock line is high will be interpreted as control signals.
相關PDF資料 |
PDF描述 |
|---|---|
| DS1077Z-125 | 125 MHz, OTHER CLOCK GENERATOR, PDSO8 |
| DS1077Z-100 | 100 MHz, OTHER CLOCK GENERATOR, PDSO8 |
| DS1100U-175/T&R | SILICON DELAY LINE, TRUE OUTPUT, PDSO8 |
| DS1100U-40/T&R | SILICON DELAY LINE, TRUE OUTPUT, PDSO8 |
| DS1100U-45/T&R | SILICON DELAY LINE, TRUE OUTPUT, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1077Z-66+ | 功能描述:可編程振蕩器 EconOscillator/Dvdr 66MHz 118mil 2-Wire RoHS:否 制造商:IDT 封裝 / 箱體:5 mm x 7 mm x 1.5 mm 頻率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 頻率穩定性:+/- 50 PPM 電源電壓:3.63 V 負載電容:10 pF 端接類型:SMD/SMT 輸出格式:LVPECL 最小工作溫度:- 40 C 最大工作溫度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封裝: |
| DS10-80B | 制造商:TRANSMISSION DEVELOPMENTS 功能描述:MOULDED SPUR GEAR 1.0, 80 |
| DS1080CL | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Spread-Spectrum Crystal Multiplier |
| DS1080CLU+ | 功能描述:時鐘發生器及支持產品 Spread-Spectrum Crystal Multiplier RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56 |
| DS1080CLU+T | 功能描述:時鐘發生器及支持產品 Spread-Spectrum Crystal Multiplier RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56 |
發布緊急采購，3分鐘左右您將得到回復。