- 您現在的位置：買賣IC網 > PDF目錄17070 > DC1011A-A (Linear Technology)BOARD DELTA SIGMA ADC LTC2498 PDF資料下載
參數資料
| 型號： | DC1011A-A |
| 廠商： | Linear Technology |
| 文件頁數： | 10/38頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD DELTA SIGMA ADC LTC2498 |
| 軟件下載： | QuikEval System |
| 設計資源： | DC1011A Schematic DC1011A Design Files |
| 標準包裝： | 1 |
| 系列： | Easy Drive™, QuikEval™ |
| ADC 的數量： | 1 |
| 位數： | 24 |
| 采樣率（每秒）： | 7.5 |
| 數據接口： | MICROWIRE?，串行，SPI? |
| 已用 IC / 零件： | LTC2498 |
| 已供物品： | 板 |
| 相關產品： | LTC2498HUHF#TRPBF-ND - IC ADC 24BIT 16CH DELTA 38-QFN LTC2498HUHF#PBF-ND - IC ADC 24BIT 16CH DELTA 38-QFN LTC2498IUHF#TRPBF-ND - IC ADC 24BIT 16CH 38-QFN LTC2498CUHF#TRPBF-ND - IC ADC 24BIT 16CH 38-QFN LTC2498IUHF#PBF-ND - IC ADC 24BIT 16CH 38-QFN LTC2498CUHF#PBF-ND - IC ADC 24BIT 16CH 38-QFN |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
LTC2498
18
2498ff
applications inForMation
INPUT DATA FORMAT
The LTC2498 serial input word is 13 bits long and contains
two distinct sets of data. The first set (SGL, ODD, A2, A1,
A0) is used to select the input channel. The second set of
data(IM,FA,FB,SPD)isusedtoselectthefrequencyrejec-
tion,speedmode(1x,2x),andtemperaturemeasurement.
After power-up, the device initiates an internal reset cycle
whichsetstheinputchanneltoCH0–CH1(IN+=CH0,IN–=
CH1),thefrequencyrejectiontosimultaneous50Hz/60Hz,
and 1x output rate (auto-calibration enabled). The first
conversion automatically begins at power-up using this
default configuration. Once the conversion is complete,
a new word may be written into the device.
The first 3 bits shifted into the device consist of two preen-
able bits and one enable bit. As demonstrated in Figure 3,
the first three bits shifted into the device enable the device
configurationandinputchannelselection.Validsettingsfor
these three bits are 000, 100 and 101. Other combinations
should be avoided. If the first three bits are 000 or 100, the
following data is ignored (don’t care) and the previously
selected input channel and configuration remain valid for
the next conversion.
If the first 3 bits shifted into the device are 101, then the
next 5 bits select the input channel for the next conversion
cycle, see Table 3.
The first input bit following the 101 sequence (SGL)
determines if the input selection is differential (SGL = 0)
or single-ended (SGL = 1). For SGL = 0, two adjacent
channels can be selected to form a differential input. For
SGL = 1, one of 16 channels is selected as the positive
input.ThenegativeinputisCOMforallsingleendedopera-
tions. The remaining 4 bits (ODD, A2, A1, A0) determine
which channel(s) is/are selected and the polarity (for a
differential input).
The next serial input bit immediately following the input
channel selection is the enable bit for the conversion
configuration (EN2). If this bit is set to 0, then the next
conversion is performed using the previously selected
converter configuration. This is useful in systems using
the same rejection/speed for all input channels and for
backwardcompatibilitywiththeLTC2418/LTC2414families
of delta sigma ADCs.
A new configuration can be loaded into the device by
setting EN2 = 1, see Table 4. The first bit (IM) is used
to select the internal temperature sensor. If IM = 1, the
following conversion will be performed on the internal
temperaturesensorratherthantheselectedinputchannel.
The next 2 bits (FA and FB) are used to set the rejection
frequency. The final bit (SPD) is used to select either the
1x output rate if SPD = 0 (auto-calibration is enabled and
the offset is continuously calibrated and removed from
Table 2. Output Data Format
Differential Input Voltage
VIN*
Bit 31
EOC
Bit 30
DMY
Bit 29
SIG
Bit 28
MSB
Bit 27
Bit 26
Bit 25
…
Bit 0
VIN* ≥ 0.5 VREF**
0
1
0
…
0
0.5 VREF** – 1LSB
0
1
0
1
…
1
0.25 VREF**
0
1
0
1
0
…
0
0.25 VREF** – 1LSB
0
1/0***
0
1
…
1
0
1
0
…
0
–1LSB
0
1
…
1
–0.25 VREF**
0
1
0
…
0
–0.25 VREF** – 1LSB
0
1
0
1
…
1
–0.5 VREF**
0
1
0
…
0
VIN* < –0.5 VREF**
0
1
…
1
*The differential input voltage VIN = IN+ – IN–. **The differential reference voltage VREF = REF+ – REF–.
***The sign bit changes state during the 0 output code when the device is operating in the 2x speed mode.
相關PDF資料 |
PDF描述 |
|---|---|
| NR5040T100M | INDUCTOR 10UH 2.1A 20% SMD |
| EVAL-AD5405EBZ | BOARD EVAL FOR AD5405 |
| EVAL-AD5062EBZ | BOARD EVAL FOR AD5062 |
| V48C2E50BL2 | CONVERTER MOD DC/DC 2V 50W |
| DC1010A-C | BOARD DELTA SIGMA ADC LTC2487 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DC1011A-B | 功能描述:BOARD DELTA SIGMA ADC LTC2496 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:Easy Drive™, QuikEval™ 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| DC1011A-C | 功能描述:BOARD DELTA SIGMA ADC LTC2494 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:Easy Drive™, QuikEval™ 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| DC-1012 | 制造商:BCM Advanced Research 功能描述:BCM NANO-ITX POWER BOARD - Bulk |
| DC1012080 WAF | 制造商:ON Semiconductor 功能描述: |
| DC1012-103L | 制造商:Coilcraft Inc 功能描述:Power inductor, 10% tol, RoHS |
發布緊急采購，3分鐘左右您將得到回復。