參數資料
型號： CS5132HGDWR24
廠商： MOTOROLA INC
元件分類： 穩壓器
英文描述： 1.5 A DUAL SWITCHING CONTROLLER, PDSO24
封裝： 0.300 INCH, MS-013, SO-24
文件頁數： 9/20頁
文件大?。?/td> 181K
代理商： CS5132HGDWR24
Application Information: continued
Therefore, the range of load currents that will cause the
internal current sense comparator to detect an overload
condition through a 3.3m embedded PCB trace is: 19.3A
< ICL < 38.7A, with 26A being the nominal overload condi-
tion.
Design Rules for Using a Droop Resistor
The basic equation for laying an embedded resistor is:
RAR = ρ ×
or R =
ρ ×
,
where
A= W
× t = cross-sectional area;
ρ= the copper resistivity (-mil);
L= length (mils);
W = width (mils);
t = thickness (mils).
For most PCBs the copper thickness, t, is 35m (1.37 mils)
for one ounce copper;
ρ = 717.86-mil.
For a CPU load of 16A the resistance needed to create a
50mV drop at full load is:
RDROOP =
=
= 3.1m.
The resistivity of the copper will drift with the temperature
according to the following guidelines:
R = 12% @ TA = +50°C;
R = 34% @TA = +100°C.
Droop Resistor Length, Width, and Thickness
The minimum width and thickness of the droop resistor
should primarily be determined on the basis of the current-
carrying capacity required, and the maximum permissible
droop resistor temperature rise. PCB manufacturer design
charts can be used in determining current- carrying capaci-
ty and sizes of etched copper conductors for various tem-
perature rises above ambient.
For single conductor applications, such as the use of the
droop resistor, PCB design charts show that for a droop
resistor with a required current-carrying capacity of 16A,
and a 45°C temperature rise above ambient, the recom-
mended cross section is 275 mil2.
W
× t = 275 mil2,
where
W = droop resistor width;
t = droop resistor thickness.
For 1oz. copper, t= 1.37 mils, therefore W = 201 mils =
0.201 in.
R =
ρ×
,
where
R = droop resistor value;
ρ = 0.71786m-mil (1 oz. copper);
L = droop resistor length;
W = droop resistor width.
RDROOP = 3.3m.
3.3m
= 0.71786m-mil ×
.
Hence, L = 1265 mils = 1.265 in.
In layouts where it is impractical to lay out a droop resistor
in a straight line 1265 mils long, the embedded PCB trace
can be “snaked” to fit within the available space.
Thermal Considerations for Power MOSFETs and Diodes
In order to maintain good reliability, the junction tempera-
ture of the semiconductor components should be kept to a
maximum of 150°C or lower. The thermal impedance
(junction to ambient) required to meet this requirement can
be calculated as follows:
Thermal Impedance =
.
A heatsink may be added to TO-220 components to reduce
their thermal impedance. A number of PC board layout
techniques such as thermal vias and additional copper foil
area can be used to improve the power handling capability
of surface mount components.
As a consequence of large currents being turned on and off
at high frequency, switching regulators generate noise as a
consequence of their normal operation. When designing
for compliance with EMI/EMC regulations, additional
components may be added to reduce noise emissions.
These components are not required for regulator operation
and experimental results may allow them to be eliminated.
The input filter inductor may not be required because bulk
filter and bypass capacitors, as well as other loads located
on the board will tend to reduce regulator di/dt effects on
the circuit board and input power supply. Placement of the
power component to minimize routing distance will also
help to reduce emissions.
EMI Management
TJ(MAX) - TA
Power
Thermal Management
L
201 mils
× 1.37 mils
L
W
× t
50mV
16A
50mV
IOUT
L
(W
× t)
L
A
17
CS5132H
相關PDF資料
PDF描述
CS5151HGDR16 1.5 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16
CS5158GD16 1.5 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16
CS52845ED14 1 A SWITCHING CONTROLLER, PDSO14
CS8442XN8 STEPPER MOTOR CONTROLLER, PDIP8
CS9ARH-FREQ1 CRYSTAL OSCILLATOR, CLOCK, 50 MHz - 300 MHz, PECL OUTPUT
相關代理商/技術參數
參數描述
CS5134AM 制造商:Rochester Electronics LLC 功能描述:- Bulk
CS5135-000 制造商:TE Connectivity 功能描述:82A1111-22-6-6 - Bulk
CS5138AA 制造商:Rochester Electronics LLC 功能描述:- Bulk
CS-514 制造商:未知廠家 制造商全稱:未知廠家 功能描述:
CS-514/R 制造商:未知廠家 制造商全稱:未知廠家 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*