- 您現在的位置：買賣IC網 > PDF目錄379935 > COP8SCR9 (National Semiconductor Corporation) 8-Bit CMOS Flash Based Microcontroller with 32k Memory, Virtual EEPROM and Brownout(8位基于CMOS 閃速存儲器的帶32K存儲器，虛擬EEPROM和電壓過低復位的微控制器) PDF資料下載
參數資料
| 型號： | COP8SCR9 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | 8-Bit CMOS Flash Based Microcontroller with 32k Memory, Virtual EEPROM and Brownout(8位基于CMOS 閃速存儲器的帶32K存儲器，虛擬EEPROM和電壓過低復位的微控制器) |
| 中文描述： | 8位CMOS閃存為基礎的32K的內存，虛擬EEPROM和欠壓（8位基于的CMOS閃速存儲器的帶32K的存儲器，微控制器虛擬的EEPROM和電壓過低復位的微控制器） |
| 文件頁數： | 24/68頁 |
| 文件大?。?/td> | 714K |
| 代理商： | COP8SCR9 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
5.0 In-System Programming
(Continued)
TABLE 13. Register and Bit Name Definitions
Register
Name
Purpose
RAM
Location
0xA9
0xA8
0xAB
ISPADHI
ISPADLO
ISPWR
High byte of Flash Memory Address
Low byte of Flash Memory Address
The user must store the byte to be written into this register before jumping into the
write byte routine.
Data will be returned to this register after the read byte routine execution.
The ISPKEY Register is required to validate the JSRB instruction and must be loaded
within 6 instruction cycles before the JSRB.
Holds the count of the number of bytes to be read or written in block operations.
Write Timing Register. This register must be loaded, by the user, with the proper
value before execution of any USER ISP Write or Erase operation. Refer to Table 9
for the correct value.
The user must place this code in the accumulator before execution of a Flash Memory
Mass Erase command.
Must be transferred to the ISPKEY register before execution of a JSRB instruction.
ISPRD
ISPKEY
0xAA
0xE2
BYTECOUNTLO
PGMTIM
0xF1
0xE1
Confirmation Code
A
KEY
0x98
5.9 RESTRICTIONS ON SOFTWARE WHEN CALLING
ISP ROUTINES IN BOOT ROM
1.
The hardware will disable interrupts from occurring. The
hardware will leave the GIE bit in its current state, and if
set, the hardware interrupts will occur when execution is
returned to Flash Memory. Subsequent interrupts, dur-
ing ISP operation, from the same interrupt source will be
lost.
2.
The security feature in the MICROWIRE/PLUS ISP is
guaranteed by software and not hardware. When ex-
ecuting the MICROWIRE/PLUS ISP routine, the security
bit is checked prior to performing all instructions. Only
the mass erase command, write PGMTIM register, and
reading the Option register is permitted within the
MICROWIRE/PLUS ISP routine. When the user is per-
forming his own ISP, all commands are permitted. The
entry points from the user’s ISP code do not check for
security. It is the burden of the user to guarantee his own
security. See the Security bit description in 4.5 OPTION
REGISTER for more details on security.
3.
When using any of the ISP functions in Boot ROM, the
ISP routines will service the WATCHDOG within the
selected upper window. Upon return to flash memory,
the WATCHDOG is serviced, the lower window is en-
abled, and the user can service the WATCHDOG any-
time following exit from Boot ROM, but must service it
within the selected upper window to avoid a WATCH-
DOG error.
4.
Block Writes can start anywhere in the page of Flash
memory, but cannot cross half page or full page bound-
aries.
5.
The user must ensure that a page erase or a mass
erase is executed between two consecutive writes to
the same location in Flash memory. Two writes to
the same location without an intervening erase will
produce unpredicatable results including possible
disturbance of unassociated locations.
5.10 FLASH MEMORY DURABILITY CONSIDERATIONS
The endurance of the Flash Memory (number of possible
Erase/Write cycles) is a function of the erase time and the
lowest temperature at which the erasure occurs. If the device
is to be used at low temperature, additional erase operations
can be used to extend the erase time. The user can deter-
mine how many times to erase a page based on what
endurance is desired for the application (e.g. four page
erase cycles, each time a page erase is done, may be
required to achieve the typical 100k Erase/Write cycles in an
application which may be operating down to 0C). Also, the
customer can verify that the entire page is erased, with
software, and request additional erase operations if desired.
TABLE 14. Typical Flash Memory Endurance
Low End of Operating Temp Range
Erase Time
40C
1 ms
60k
2 ms
60k
3 ms
60k
4 ms
60k
5 ms
70k
6 ms
80k
7 ms
90k
8 ms
100k
20C
60k
60k
60k
60k
70k
80k
90k
100k
0C
60k
60k
60k
100k
100k
100k
100k
100k
25C
100k
100k
100k
100k
100k
100k
100k
100k
>
25C
100k
100k
100k
100k
100k
100k
100k
100k
C
www.national.com
24
相關PDF資料 |
PDF描述 |
|---|---|
| COP8SDR9 | 8-Bit CMOS Flash Based Microcontroller with 32k Memory, Virtual EEPROM and Brownout(8位基于CMOS 閃速存儲器的帶32K存儲器，虛擬EEPROM和電壓過低復位的微控制器) |
| COP8SER7-XE | 8-Bit CMOS ROM Based and OTP Microcontrollers with 4k Memory and 128 Bytes EERAM |
| COP8SEC5 | 8-Bit CMOS ROM Based and OTP Microcontrollers with 4k Memory and 128 Bytes EERAM |
| COP8SEC516M | 8-Bit CMOS ROM Based and OTP Microcontrollers with 4k Memory and 128 Bytes EERAM |
| COP8SEC520M | 8-Bit CMOS ROM Based and OTP Microcontrollers with 4k Memory and 128 Bytes EERAM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| COP8SCR9HLQ7 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:8-Bit CMOS Flash Based Microcontroller with 32k Memory, Virtual EEPROM and Brownout |
| COP8SCR9HLQ8 | 功能描述:IC ADC FLASH 8BIT EE 44-LLP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:COP8™ 8S 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323 |
| COP8SCR9HVA7 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:8-Bit CMOS Flash Based Microcontroller with 32k Memory, Virtual EEPROM and Brownout |
| COP8SCR9HVA8 | 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| COP8SCR9HVA8 NOPB | 制造商:National Semiconductor 功能描述:MCU 8-bit COP8 CISC 32KB Flash 3.3V/5V 44-Pin PLCC Rail |
發布緊急采購，3分鐘左右您將得到回復。