- 您現在的位置：買賣IC網 > PDF目錄16461 > CDB4955A (Cirrus Logic Inc)EVALUATION BOARD FOR CS4955A PDF資料下載
參數資料
| 型號： | CDB4955A |
| 廠商： | Cirrus Logic Inc |
| 文件頁數： | 49/60頁 |
| 文件大小： | 0K |
| 描述： | EVALUATION BOARD FOR CS4955A |
| 標準包裝： | 1 |
| 主要目的： | 視頻，視頻處理 |
| 嵌入式： | 是，其它 |
| 已用 IC / 零件： | CS4955 |
| 主要屬性： | NTSC/PAL 數字視頻編碼器 |
| 次要屬性： | 圖形用戶界面，RS-232 接口 |
| 已供物品： | 板 |
| 相關產品： | CS4954-CQZR-ND - IC VID ENCODER NTSC/PAL 48-TQFP 598-1682-ND - IC VIDEO ENCODER NTSC/PAL 48TQFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁當前第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁
CS4954 CS4955
DS278F6
53
9.
BOARD DESIGN AND LAYOUT
CONSIDERATIONS
The printed circuit layout should be optimized for
lowest noise on the CS4954/5 placed as close to the
output connectors as possible. All analog supply
traces should be as short as possible to minimize in-
ductive ringing.
A well designed power distribution network is es-
sential in eliminating digital switching noise. The
ground planes must provide a low-impedance re-
turn path for the digital circuits. A PC board with a
minimun of four layers is recommended. The
ground layer should be used as a shield to isolate
noise from the analog traces. The top layer (1)
should be reserved for analog traces but digital
traces can share this layer if the digital signals have
sufficiently slow edges and edge rates and switch
little current or if they are separated from the ana-
log traces by a signigicant distance (dependent on
their frequency content and current). The PCB lay-
er “stack up” (from top to bottom) should be: ana-
log/digital signal then ground plane followed by
the analog power plane and the digital signal layer.
9.1
Power and Ground Planes
The power and ground planes need isolation gaps
of at least 0.05" to minimize digital switching noise
effects on the analog signals and components. A
split analog/digital ground plane should be con-
nected at one location as close as possible to the
CS4954/5.
9.2
Power Supply Decoupling
Start by reducing power supply ripple and wiring
harness inductance by placing a large (33-100 uF)
capacitor as close to the power entry point as pos-
sible. Use separate power planes or traces for the
digital and analog sections even if they use the
same supply. If necessary, further isolate the digital
and analog power supplies by using ferrite beads on
each supply branch followed by a low ESR capac-
itor.
Place all decoupling caps as close as possible to the
device. Surface mount capacitors generally have
lower inductance than radial lead or axial lead com-
ponents. Surface mount caps should be place on the
component side of the PCB to minimize inductance
caused by board vias. Any vias, especially to
ground, should be as large as possible to reduce
their inductive effects.
9.3
Digital Interconnect
The digital inputs and outputs of the CS4954/5
should be isolated from the analog outputs as much
as possible. Use separate signal layers whenever
possible and do not route digital signals over the
analog power and ground planes.
Noise from the digital section is related to the digi-
tal edge rates and rise/fall times. Ringing, over-
shoot, undershoot, and ground bounce are all
related to edge rise/fall times. Use lower speed log-
ic such as HCMOS for the host port interface to re-
duce switching noise. For the video input ports,
higher speed logic is required, but use logic that
produces the slowest practical edge rise/fall times
to reduce noise. It is also important to match the
source impedance, line impedance, and load im-
pedance as much as possible. Generally, if the line
length is greater than one fourth of the signal wave-
length or period (from
λ = ν/f), a line termination is
necessary. Ringing can also be reduced by damping
the line with a series resistor (22-150
Ω). Under ex-
treme cases, it may be advisable to use microstrip
techniques to further reduce radiated switching
noise if there are very fast (<2 ns) rise/fall times in
the system. If microstrip techniques are used, split
the analog and digital ground planes and use proper
RF decoupling techniques.
9.4
Analog Interconnect
The CS4954/5 should be located as close as possi-
ble the output connectors to minimize noise pickup
and reflections due to impedance mismatch. All un-
used analog outputs should be placed in shutdown.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-241-EX | CONVERTER MOD DC/DC 12V 75W |
| EB43-S0C2040X | CONN EDGEBOARD DUAL 40POS 3A |
| M3TTK-1436R | IDC CABLE - MSD14K/MC14M/MSD14K |
| GSM10DRTI-S13 | CONN EDGECARD 20POS .156 EXTEND |
| M3DYK-1006J | IDC CABLE - MKR10K/MC10G/MPD10K |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CDB-496122-EV2 | 制造商:Cirrus Logic 功能描述: |
| CDB496122-EV2 | 功能描述:音頻 IC 開發工具 Eval Bd CobraNet Trnspt/AdNtwrk Prcsr RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| CDB49X | 制造商:Cirrus Logic 功能描述:EVAL BD - BASE BOARD FOR AUDIO DSP - Boxed Product (Development Kits) |
| CDB-5 | 功能描述:電線導管 5’ Brown RoHS:否 制造商:Panduit 類型:Slotted SideWall Open finger design wiring cut 材料:Polypropylene 顏色:Light Gray 大小: 最大光束直徑: 抗拉強度: 外部導管寬度:25 mm 外部導管高度:25 mm |
| CDB5012 | 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:Evaluation Board |
發布緊急采購，3分鐘左右您將得到回復。