參數資料
型號： bq2060
廠商： Benchmark Technology Group
英文描述： SBS v1.1-Compliant Gas Gauge IC(Gas Gauge芯片)
中文描述： 銀紫荊星章1.1版兼容的氣體計IC（電量監測計芯片）
文件頁數： 17/45頁
文件大?。?/td> 457K
代理商： BQ2060
Command 0x26 with the pack unsealed. A reset
send after this step resets RM to zero.
3.
Issue the Enable Low-Power Storage Mode com-
mand.
4.
Within 900–1600ms after sending the Enable
Low-Power command, issue the Enable VFC Cali-
bration command. This delays the low-power stor-
age mode until after VFC calibration completion.
5.
Issue the SEAL Command subsequent to the VFC
Calibration command. The bq2060 must receive the
SEAL Command before VFC calibration completes.
The bq2060 resets the OCE bit in Pack Status
when calibration begins and sets the bit when cali-
bration successfully completes.
After VF C calibration completes automatically, the
bq2060 saves the VF C offset cancellation values in
E E PROM and enters the low-power storage mode in
about 20s. In addition, the bq2060 is sealed, allowing ac-
cess as defined in Table3 only.
Purpose:
The ManufacturerAccess() function provides the system
host access to bq2060 functions that are not defined by
theSBD.
SMBus Protocol:
Read or WriteWord
Input/Output:
Word
RemainingCapacityAlarm() (0x01); [0x01]
Description:
Sets or gets the low-capacity threshold value. Whenever
the RemainingCapacity() falls below the low capacity
value, the bq2060 sends AlarmWarning() messages to
the SMBus H ost with the R E MAINING_CAPAC-
ITY_ALARM bit set. A low-capacity value of 0 disables
this alarm.
The bq2060 initially sets the low-capacity
value to
Remaining Capacity Alarm
value programmed
in EE 0x04 - 0x05. The low-capacity value remains un-
changed
until
altered
CapacityAlarm() function. The low-capacity value may
be expressed in either current (mA) or power (10mWh)
depending on the setting of the BatteryMode()’s CAPAC-
ITY_MODE bit.
by
the
R emaining-
Purpose:
The RemainingCapacityAlarm() function can be used by
systems that know how much power they require to save
their operating state. It enables those systems to more
finely control the point at which they transition into sus-
pend or hibernate state. The low-capacity value can be
read to verify the value in use by the bq2060’s low capac-
ity alarm.
SMBus Protocol:
Read or WriteWord
Input/Output:
Unsigned integer—value below which
Low Capacity messages aresent.
Battery Modes
CAPACITY_MODE
bit = 0
mAh @C/5
0–65,535mAh
CAPACITY_MODE
bit = 1
10mWh @P/5
0–65,535 10mWh
Not applicable
See RemainingCapacity()
Units
Range
Granularity
Accuracy
RemainingTimeAlarm() (0x02); [0x02]
Description:
Sets or gets the remaining time alarm value. Whenever
the AverageTimeToEmpty() falls below the remaining time
value, the bq2060 sends AlarmWarning() messages to the
SMBus Host with the REMAINING_TIME_ALARM bit
set. A remaining time value of 0 effectively disables this
alarm. The bq2060 initially sets the remaining time value
to the
Remaining Time Alarm
value programmed in EE
0x02 - 0x03. The remaining time value remains unchanged
until alteredby theRemainingTimeAlarm() function.
Purpose:
The RemainingTimeAlarm() function can be used by
systems that want to adjust when the remaining time
alarm warning is sent. The remaining time value can
be read to verify the value in use by the bq2060’s
RemainingTimeAlarm().
SMBus Protocol:
Read or WriteWord
Input/Output:
Unsigned integer—the point below which remain-
ing timemessages aresent.
Units: minutes
Range: 0 to65,535 minutes
Granularity: Not applicable
Accuracy: seeAverageTimeToEmpty()
BatteryMode() (0x03); [0x03]
Description:
This function selects the various battery operational
modes and reports thebattery’s modeand requests.
Defined modes include:
Whether
specified in mAh or 10mWh (CAPACITY_MODE bit)
the
battery’s
capacity
information
is
Whether the ChargingCurrent() and ChargingVoltage()
values are broadcast to the Smart Battery Charger
when the bq2060 detects the battery requires charging
(CHARGER_MODE bit)
Whether all broadcasts to the Smart Battery Charger
and Host aredisabled
17
bq2060
相關PDF資料
PDF描述
bq2092 Gas Gauge IC with SMBus-Like Interface(Gas Gauge芯片（帶SMBus 接口）)
bq2201 SRAM Nonvolatile Controller Unit(靜態RAM非易失性控制器單元)
bq2202 SRAM Nonvolatile Controller With Reset(靜態RAM非易失性控制器單元(帶復位）)
bq2502 Integrated Backup Unit(完整的后備單元)
bq2945 Gas Gauge IC with SMBus Interface(Gas Gauge芯片（帶SMBus 接口）)
相關代理商/技術參數
參數描述
BQ2060A 制造商:TI 制造商全稱:Texas Instruments 功能描述:SBS v1.1-Compliant Gas Gauge IC
BQ2060ADBQ 功能描述:電池管理 SBS V1.1 Compliant GG IC RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel
BQ2060ADBQG4 功能描述:電池管理 SBS V1.1 Compliant GG IC RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel
BQ2060ADBQR 功能描述:電池管理 SBS V1.1 Compliant RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel
BQ2060ADBQRG4 功能描述:電池管理 SBS V1.1 Compliant RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*