- 您現在的位置：買賣IC網 > PDF目錄385186 > bq2014 (Benchmark Technology Group) Gas Gauge IC with External Charge Control(氣體Gauge（帶外部電荷控制）) PDF資料下載
參數資料
| 型號： | bq2014 |
| 廠商： | Benchmark Technology Group |
| 英文描述： | Gas Gauge IC with External Charge Control(氣體Gauge（帶外部電荷控制）) |
| 中文描述： | 氣體計IC（氣體壓力表與外部充電控制（帶外部電荷控制）） |
| 文件頁數： | 4/21頁 |
| 文件大小： | 219K |
| 代理商： | BQ2014 |
Voltage Thresholds
In conjunction with monitoring V
SR
for charge/discharge
currents, the bq2014 monitors the single-cell battery po-
tential through the SB pin. The single-cell voltage po-
tential is determined through a resistor/divider network
per the following equation:
R
R
3
N
2
1
=
where N is the number of cells, R2 is connected to the
positive battery terminal, and R3 is connected to the
negative battery terminal. The single-cell battery volt-
age is monitored for the end-of-discharge voltage (EDV)
and for maximum cell voltage (MCV).
levels are used to determine when the battery has
reached an “empty” state, and the MCV threshold is used
for fault detection during charging.
EDV threshold
Two EDV thresholds for the bq2014 are programmable
with the default values fixed at:
EDV1 (early warning) = 1.05V
EDVF (empty) = 0.95V
If V
SB
is below either of the two EDV thresholds, the as-
sociated flag is latched and remains latched, independ-
ent of V
SB
, until the next valid charge (as defined in the
section entitled “Gas Gauge Operation”). The V
SB
value
is also available over the serial port.
During discharge and charge, the bq2014 monitors V
SR
for various thresholds. These thresholds are used to
compensate the charge and discharge rates. Refer to the
count compensation section for details. EDV monitoring
is disabled if V
SR
≤
-250mV typical and resumes sec-
ond after V
SR
> -250mV.
EMPTY Output
The EMPTY output switches to high impedance when
V
SB
< V
EDF
and remains latched until a valid charge oc-
curs.
Reset
The bq2014 recognizes a valid battery whenever V
SB
is
greater than 0.1V typical. V
SB
rising from below 0.25V
or falling from above 2.25V (V
MCV
) resets the device. Re-
set can also be accomplished with a command over the
serial port as described in the Reset Register section.
Temperature
The bq2014 internally determines the temperature in
10°C steps centered from -35°C to +85°C. The tempera-
ture steps are used to adapt charge and discharge rate
compensations, self-discharge counting, and available
charge display translation.
available over the serial port in 10°C increments as
shown below:
The temperature range is
Layout Considerations
The bq2014 measures the voltage differential between
the SR and V
SS
pins. V
OS
(the offset voltage at the SR
pin) is greatly affected by PC board layout. For optimal
results, the PC board layout should follow the strict rule
of a single-point ground return. Sharing high-current
ground with small signal ground causes undesirable
noise on the small signal nodes. Additionally:
The capacitors (C2 and C3) should be placed as close as
possible to the SB and V
CC
pins, respectively, and their
paths to V
SS
should be as short as possible. A
high-quality ceramic capacitor of 0.1
μ
f is recommended
for V
CC
.
The sense resistor (R1, C1) should be placed as close
as possible to the SR pin.
The sense resistor (R16) should be as close as
possible to the bq2014.
4
bq2014
TMPGG (hex)
Temperature Range
0x
< -30°C
1x
-30°C to -20°C
2x
-20°C to -10°C
3x
-10°C to 0°C
4x
0°C to 10°C
5x
10°C to 20°C
6x
20°C to 30°C
7x
30°C to 40°C
8x
40°C to 50°C
9x
50°C to 60°C
Ax
60°C to 70°C
Bx
70°C to 80°C
Cx
> 80°C
相關PDF資料 |
PDF描述 |
|---|---|
| bq2040 | Gas Gauge IC With SMBus Interface(氣體Gauge芯片（帶SMBus 接口）) |
| bq2050H | Low-Cost Lithium Ion Power Gauge IC(低價格鋰離子電源氣體Gauge芯片) |
| bq2050 | Lithium Ion Power Gauge IC(鋰離子電源Gause 芯片) |
| bq2052 | Gas Gauge IC for Lithium Primary Cells(Gas Gauge 芯片（用于鋰電池）) |
| bq2060 | SBS v1.1-Compliant Gas Gauge IC(Gas Gauge芯片) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BQ2014H | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Low-Cost NiCd/NiMH Gas Gauge IC |
| BQ2014HEVM-001 | 功能描述:電源管理IC開發工具 BQ2014H Eval Kit for NiMH 10.8V RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| BQ2014HSN | 功能描述:電池管理 NiCd/NiMH Gas Gauge RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| BQ2014HSN-A309 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Low-Cost NiCd/NiMH Gas Gauge IC |
| BQ2014HSNG4 | 功能描述:電池管理 NiCd/NiMH Gas Gauge RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。