- 您現在的位置：買賣IC網 > PDF目錄385186 > bq2014 (Benchmark Technology Group) Gas Gauge IC with External Charge Control(氣體Gauge（帶外部電荷控制）) PDF資料下載
參數資料
| 型號： | bq2014 |
| 廠商： | Benchmark Technology Group |
| 英文描述： | Gas Gauge IC with External Charge Control(氣體Gauge（帶外部電荷控制）) |
| 中文描述： | 氣體計IC（氣體壓力表與外部充電控制（帶外部電荷控制）） |
| 文件頁數： | 13/21頁 |
| 文件大?。?/td> | 219K |
| 代理商： | BQ2014 |
Temperature and Gas Gauge Register
(TMPGG)
The read-only TMPGG register (address=02h) contains
two data fields. The first field contains the battery tem-
perature. The second field contains the available charge
from the battery.
The bq2014 contains an internal temperature sensor.
The temperature is used to set charge and discharge ef-
ficiency factors as well as to adjust the self-discharge co-
efficient.
The temperature register contents may be
translated as shown in Table 7.
The bq2014 calculates the available charge as a function
of NAC, temperature, and LMD. The results of the cal-
culation are available via the display port or the gas
gauge field of the TMPGG register. The register is used
to give available capacity in
116
increments from 0 to
1516
.
The gas gauge display and the gas gauge portion of the
TMPGG register are adjusted for cold temperature de-
pendencies. A piece-wise correction is performed as fol-
lows:
The adjustment between > 0°C and -20°C < T < 0°C has a
10°C hysteresis.
Nominal Available Charge Register
(NACH/NACL)
The read/write NACH register (address=03h) and the
read-only NACL low-byte register (address=17h) are the
main gas gauging registers for the bq2014. The NAC
registers are incremented during charge actions and
decremented during discharge and self-discharge ac-
tions.
The correction factors for charge/discharge effi-
ciency are applied automatically to NAC.
On reset, NACH and NACL are cleared to 0. When the
bq2014 detects a charge, NACL resets to 0. NACH and
NACL are reset to 0 on the first valid charge after V
SB
=
EDV1.
Writing to the NAC registers affects the available
charge counts and, therefore, affects the bq2014 gas
gauge operation.
Do not write the NAC registers to a
value greater than
LMD.
Battery Identification Register (BATID)
The read/write BATID register (address=04h) is avail-
able for use by the system to determine the type of bat-
tery pack. The BATID contents are retained as long as
V
CC
is greater than 2V. The contents of BATID have no
effect on the operation of the bq2014. There is no de-
fault setting for this register.
Last Measured Discharge Register (LMD)
LMD is a read/write register (address=05h) that the
bq2014 uses as a measured full reference. The bq2014
adjusts LMD based on the measured discharge capacity
of the battery from full to empty. In this way the bq2014
updates the capacity of the battery. LMD is set to PFC
during a bq2014 reset.
Secondary Status Flags Register (FLGS2)
The read-only FLGS2 register (address=06h) contains
the secondary bq2014 flags.
The
charge rate
flag (CR) is used to denote the fast
charge regime.
Fast charge is assumed whenever a
charge action is initiated. The CR flag remains asserted
if the charge rate does not fall below 2 counts/sec.
13
Temperature
Available Capacity Calculation
> 0°C
NAC / “Full Reference”
-20°C < T < 0°C
0.75*NAC / “Full Reference”
0.5*NAC / “Full Reference”
< -20°C
TMP3
0
0
0
0
0
0
0
0
1
1
1
1
1
TMP2
0
0
0
0
1
1
1
1
0
0
0
0
1
TMP1
0
0
1
1
0
0
1
1
0
0
1
1
0
TMP0
0
1
0
1
0
1
0
1
0
1
0
1
0
Temperature
T < -30°C
-30°C < T < -20°C
-20°C < T < -10°C
-10°C < T < 0°C
0°C < T < 10°C
10°C < T < 20°C
20°C < T < 30°C
30°C < T < 40°C
40°C < T < 50°C
50°C < T < 60°C
60°C < T < 70°C
70°C < T < 80°C
T > 80°C
Table 7. Temperature Register Translation
TMPGG Gas Gauge Bits
5
4
-
-
GG3
7
-
6
-
3
2
1
0
GG2
GG1
GG0
TMPGG Temperature Bits
5
4
TMP2
TMP1
7
6
3
-
2
-
1
-
0
TMP3
TMP0
bq2014
相關PDF資料 |
PDF描述 |
|---|---|
| bq2040 | Gas Gauge IC With SMBus Interface(氣體Gauge芯片（帶SMBus 接口）) |
| bq2050H | Low-Cost Lithium Ion Power Gauge IC(低價格鋰離子電源氣體Gauge芯片) |
| bq2050 | Lithium Ion Power Gauge IC(鋰離子電源Gause 芯片) |
| bq2052 | Gas Gauge IC for Lithium Primary Cells(Gas Gauge 芯片（用于鋰電池）) |
| bq2060 | SBS v1.1-Compliant Gas Gauge IC(Gas Gauge芯片) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BQ2014H | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Low-Cost NiCd/NiMH Gas Gauge IC |
| BQ2014HEVM-001 | 功能描述:電源管理IC開發工具 BQ2014H Eval Kit for NiMH 10.8V RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| BQ2014HSN | 功能描述:電池管理 NiCd/NiMH Gas Gauge RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| BQ2014HSN-A309 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Low-Cost NiCd/NiMH Gas Gauge IC |
| BQ2014HSNG4 | 功能描述:電池管理 NiCd/NiMH Gas Gauge RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。