- 您現在的位置：買賣IC網 > PDF目錄385186 > bq2014 (Benchmark Technology Group) Gas Gauge IC with External Charge Control(氣體Gauge（帶外部電荷控制）) PDF資料下載
參數資料
| 型號： | bq2014 |
| 廠商： | Benchmark Technology Group |
| 英文描述： | Gas Gauge IC with External Charge Control(氣體Gauge（帶外部電荷控制）) |
| 中文描述： | 氣體計IC（氣體壓力表與外部充電控制（帶外部電荷控制）） |
| 文件頁數： | 15/21頁 |
| 文件大小： | 219K |
| 代理商： | BQ2014 |
Reset Register (RST)
The reset register (address=39h) provides the means to
perform a software-controlled reset of the device.
writing the RST register contents from 00h to 80h, a
bq2014 reset is performed.
Setting any bit other than
the most-significant bit of the RST register is
not al-
lowed
,and results in improper operation of the bq2014.
By
Resetting the bq2014 sets the following:
LMD = PFC
CPI, VDQ, NAC, and NACL = 0
CI and BRP = 1
Note:
Self-discharge is disabled when PROG
5
= H.
Display
The bq2014 can directly display capacity information us-
ing low-power LEDs.
If LEDs are used, the program
pins should be resistively tied to V
CC
or V
SS
for a pro-
gram high or program low,respectively..
The bq2014 displays the battery charge state in relative
mode.
In relative mode, the battery charge is repre-
sented as a percentage of the LMD. Each LED segment
represents 20% of the LMD.
The capacity display is also adjusted for the present bat-
tery temperature. The temperature adjustment reflects
the available capacity at a given temperature but does
not affect the NAC register.
ments are detailed in the TMPGG register description.
The temperature adjust-
When DISP is tied to V
CC
, the SEG
1–5
outputs are inac-
tive.
Note: DISP must be tied to V
CC
if the LEDs
are not used.
When DISP is left floating, the display
becomes active whenever the NAC registers are count-
ing at a rate equivalent to V
SRO
< -4mV or charge cur-
rent is detected, V
SRO
> V
SRQ
. When pulled low, the seg-
ment outputs become active immediately.
tied to DISP allows the display to remain active for a
short period of time after activation by a push-button
switch.
A capacitor
The segment outputs are modulated as two banks of
three, with segments 1, 3, and 5 alternating with seg-
ments 2 and 4. The segment outputs are modulated at
approximately 100Hz, with each segment bank active
for 30% of the period.
SEG
1
blinks at a 4Hz rate whenever V
SB
has been de-
tected to be below V
EDV1
(EDV1 = 1), indicating a low-
battery condition. V
SB
below V
EDVF
(EDVF = 1) disables
the display output.
Microregulator
The bq2014 can operate directly from 3 or 4 cells. To facili-
tate the power supply requirements of the bq2014, an REF
output is provided to regulate an external low-threshold n-
FET. A micropower source for the bq2014 can be inexpen-
sively built using the FET and an external resistor; see
Figure 1.
15
bq2014
相關PDF資料 |
PDF描述 |
|---|---|
| bq2040 | Gas Gauge IC With SMBus Interface(氣體Gauge芯片（帶SMBus 接口）) |
| bq2050H | Low-Cost Lithium Ion Power Gauge IC(低價格鋰離子電源氣體Gauge芯片) |
| bq2050 | Lithium Ion Power Gauge IC(鋰離子電源Gause 芯片) |
| bq2052 | Gas Gauge IC for Lithium Primary Cells(Gas Gauge 芯片（用于鋰電池）) |
| bq2060 | SBS v1.1-Compliant Gas Gauge IC(Gas Gauge芯片) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BQ2014H | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Low-Cost NiCd/NiMH Gas Gauge IC |
| BQ2014HEVM-001 | 功能描述:電源管理IC開發工具 BQ2014H Eval Kit for NiMH 10.8V RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| BQ2014HSN | 功能描述:電池管理 NiCd/NiMH Gas Gauge RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| BQ2014HSN-A309 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Low-Cost NiCd/NiMH Gas Gauge IC |
| BQ2014HSNG4 | 功能描述:電池管理 NiCd/NiMH Gas Gauge RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。