- 您現在的位置：買賣IC網 > PDF目錄385186 > bq2014 (Benchmark Technology Group) Gas Gauge IC with External Charge Control(氣體Gauge（帶外部電荷控制）) PDF資料下載
參數資料
| 型號： | bq2014 |
| 廠商： | Benchmark Technology Group |
| 英文描述： | Gas Gauge IC with External Charge Control(氣體Gauge（帶外部電荷控制）) |
| 中文描述： | 氣體計IC（氣體壓力表與外部充電控制（帶外部電荷控制）） |
| 文件頁數： | 14/21頁 |
| 文件大?。?/td> | 219K |
| 代理商： | BQ2014 |
The CR values are:
Where CR is:
0
When charge rate falls below 2 counts/sec
1
When charge rate is above 2 counts/sec
The fast charge regime efficiency factors are used when
CR = 1. When CR = 0, the trickle charge efficiency fac-
tors are used. The time to change CR varies due to the
user-selectable count rates.
The
discharge rate
flags,DR2–0,are bits 6–4.
They are used to determine the current discharge re-
gime as follows:
The
overload
flag (OVLD) is asserted when a discharge
overload is detected, V
SR
< -250mV. OVLD remains as-
serted as long as the condition persists and is cleared af-
ter V
SR
> -150mV. The overload condition is used to stop
sampling of the battery terminal characteristics for
end-of-discharge determination when excessive dis-
charges occur.
DR2–0 and OVLD are set based on the measurement of the
voltage at the SR pin relative to V
SS
. The rate at which
this measurement is made varies with device activity.
Program Pin Pull-Down Register (PPD)
The read-only PPD register (address=07h) contains some
of the programming pin information for the bq2014. The
segment drivers, SEG
1–5
and DONE, have corresponding
PPD register locations, PPD
1–6
. A given location is set if a
pull-down resistor has been detected on its corresponding
segment driver.
For example, if SEG
1
and SEG
4
have
pull-down resistors, the contents of PPD are xx101001.
(
Note:
DONE must be pulled down for proper operation.)
Program Pin Pull-Up Register (PPU)
The read-only PPU register (address=08h) contains the
rest of the programming pin information for the bq2014.
The segment drivers, SEG
1–5
and DONE, have corre-
sponding PPU register locations, PPU
1–6
. A given loca-
tion is set if a pull-up resistor has been detected on its
corresponding segment driver. For example, if SEG
3
and
DONE have pull-up resistors, the contents of PPU are
xx100100.
Capacity Inaccurate Count Register (CPI)
The read-only CPI register (address=09h) is used to in-
dicate the number of times a battery has been charged
without an LMD update. Because the capacity of a re-
chargeable battery varies with age and operating condi-
tions, the bq2014 adapts to the changing capacity over
time.
A complete discharge from full (NAC=LMD) to
empty (EDV1=1) is required to perform an LMD update
assuming there have been no intervening valid charges,
the temperature is greater than or equal to 0
°
C, and the
self-discharge counter is less than 4096 counts.
The CPI register is incremented every time a valid
charge is detected. When NAC > 0.94
LMD, however,
the CPI register increments on the first valid charge;
CPI does not increment again for a valid charge until
NAC < 0.94
LMD. This prevents continuous trickle
charging from incrementing CPI if self-discharge decre-
ments NAC. The CPI register increments to 255 with-
out rolling over. When the contents of CPI are incre-
mented to 64, the capacity inaccurate flag, CI, is as-
serted in the FLGS1 register. The CPI register is reset
whenever an update of the LMD register is performed,
and the CI flag is also cleared.
Digital Magnitude Filter (DMF)
The read-write DMF register (address=0Ah) provides
the system with a means to change the default settings
of the digital magnitude filter. By writing different val-
ues into this register, the limits of V
SRD
and V
SRQ
can be
adjusted.
Note:
Care should be taken when writing to this regis-
ter. A V
SRD
and V
SRQ
below the specified V
OS
may ad-
versely affect the accuracy of the bq2014. Refer to Table
4 for recommended settings for the DMF register.
14
bq2014
FLGS2 Bits
4
-
7
-
6
-
5
-
3
-
2
-
1
-
0
OVLD
PPD/PPU Bits
8
7
6
5
4
3
2
1
-
-
-
-
PPU
6
PPU
5
PPU
4
PPU
3
PPU
2
PPU
1
PPD
6
PPD
5
PPD
4
PPD
3
PPD
2
PPD
1
FLGS2 Bits
4
DR1
7
-
6
5
3
-
2
-
1
-
0
DR2
DR0
DR2
0
0
DR1
0
0
DR0
0
1
V
SR
(V)
V
SR
> -150mV
V
SR
< -150mV
FLGS2 Bits
4
-
7
6
-
5
-
3
-
2
-
1
-
0
-
CR
相關PDF資料 |
PDF描述 |
|---|---|
| bq2040 | Gas Gauge IC With SMBus Interface(氣體Gauge芯片（帶SMBus 接口）) |
| bq2050H | Low-Cost Lithium Ion Power Gauge IC(低價格鋰離子電源氣體Gauge芯片) |
| bq2050 | Lithium Ion Power Gauge IC(鋰離子電源Gause 芯片) |
| bq2052 | Gas Gauge IC for Lithium Primary Cells(Gas Gauge 芯片（用于鋰電池）) |
| bq2060 | SBS v1.1-Compliant Gas Gauge IC(Gas Gauge芯片) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BQ2014H | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Low-Cost NiCd/NiMH Gas Gauge IC |
| BQ2014HEVM-001 | 功能描述:電源管理IC開發工具 BQ2014H Eval Kit for NiMH 10.8V RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| BQ2014HSN | 功能描述:電池管理 NiCd/NiMH Gas Gauge RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| BQ2014HSN-A309 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Low-Cost NiCd/NiMH Gas Gauge IC |
| BQ2014HSNG4 | 功能描述:電池管理 NiCd/NiMH Gas Gauge RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。