- 您現在的位置：買賣IC網 > PDF目錄385185 > bq2011K (Benchmark Technology Group) Gas Gauge IC for High Discharge Rates(用于高放電率的氣體Gauge芯片) PDF資料下載
參數資料
| 型號： | bq2011K |
| 廠商： | Benchmark Technology Group |
| 英文描述： | Gas Gauge IC for High Discharge Rates(用于高放電率的氣體Gauge芯片) |
| 中文描述： | 氣體計IC，高放電率（用于高放電率的氣體計芯片） |
| 文件頁數： | 13/20頁 |
| 文件大小： | 175K |
| 代理商： | BQ2011K |
The fast charge regime efficiency factors are used when
CR = 1. When CR = 0, the trickle charge efficiency fac-
tors are used. The time to change CR varies due to the
user-selectable count rates.
The
discharge rate
flags,DR2–0,are bits 6–4.
They are used to determine the present discharge re-
gime as follows:
The
overload
flag (OVLD) is asserted when a discharge
overload is detected, V
SRO
> 60mV. OVLD remains as-
serted as long as the condition is valid.
OutputControlRegister(OCTL)
The write-only OCTL register (address=0ah) provides the
system with a means to check the display connections for
the bq2011K. The segment drivers may be overwritten by
data from OCTL when the least-significant bit of OCTL,
OCE, is set. The data in bits OC
5–1
of the OCTL register
(see Table 5 for details) is output onto the segment pins,
SEG
5–1
, respectively if OCE=1.
Whenever OCE is written
to 1, the MSB of OCTL should be set to a 1.
The OCE reg-
ister location must be cleared to return the bq2011K to
normal operation. OCE may be cleared by either writing
the bit to a logic zero via the serial port or by resetting the
bq2011K as explained below.
Note:
Whenever the OCTL
register is written, the MSB of OCTL should be written to a
logicone.
Reset Register (RST)
The reset register (address=39h) provides the means to
perform a software-controlled reset of the device. A full
device reset may be accomplished by first writing LMD
(address = 05h) to 00h and then writing the RST regis-
ter contents from 00h to 80h.
Setting any bit other than
the most-significant bit of the RST register is
not al-
lowed
, and results in improper operation of the
bq2011K.
Resetting the bq2011K sets the following:
I
LMD = PFC
I
VDQ, OCE, and NAC = 0
(NAC = PFC when PROG
4
= L)
I
BRP = 1
Display
The bq2011K can directly display capacity information
using low-power LEDs. If LEDs are used, the segment
pins should be tied to V
CC
, the battery, or the LCOM pin
through resistors for programming the bq2011K.
The bq2011K displays the battery charge state in abso-
lute mode. In absolute mode, each segment represents a
fixed amount of charge, based on the initial PFC. In ab-
solute mode, each segment represents 20% of the PFC.
As the battery wears out over time, it is possible for the
LMD to be below the initial PFC. In this case, all of the
LEDs may not turn on, representing the reduction in
the actual battery capacity.
The capacity display is also adjusted for the present bat-
tery temperature.
The temperature adjustment reflects
the available capacity at a given temperature but does not
affect the NAC register. The temperature adjustments are
detailed in the TMPGG register description.
When DISP is tied to V
CC
, the SEG
1–5
outputs are inac-
tive. When DISP is left floating, the display becomes ac-
tive during charge if the NAC registers are counting at a
rate equivalent to V
SRO
< -2mV or fast discharge if the
NAC registers are counting at a rate equivalent to V
SRO
> 2mV. When DISP is left floating, the display also be-
comes active after the detection of a discharge signal
with a minimum amplitude of V
SR
> 20mV (10A for R
S
=
0.002
) and a minimum pulse width of 25ms. When
DISP is pulled low, the segment outputs become active
for 4s,
±
0.5s.
13
bq2011K
FLGS2 Bits
7
6
5
4
3
2
1
0
-
DR2
DR1
DR0
-
-
-
DR2
DR1
DR0
V
SRO
(mV)
0
0
0
0
10
<
≤
V
SRO
V
SRO
<
V
SRO
<
V
SRO
V
SRO
>
60
0
0
1
10
20
<
≤
0
1
0
20
40
≤
0
1
1
40
60
≤
1
0
0
FLGS2 Bits
7
6
5
4
3
2
1
0
-
-
-
-
-
-
-
OVLD
相關PDF資料 |
PDF描述 |
|---|---|
| bq2011 | Gas Gauge IC for High Discharge Rates(用于高放電率的氣體Gauge芯片) |
| bq2012 | Gas Gauge IC With Slow-Charge Control(Gas Gauge芯片（帶慢充電控制）) |
| bq2013H | Gas Gauge IC for Power-Assist Applications(應用于電源援助的氣體Gauge芯片) |
| bq2014H | Low-Cost NiCd/NiMH Gas Gauge IC(低價格NiCd/NiMHGas Gauge芯片) |
| bq2014 | Gas Gauge IC with External Charge Control(氣體Gauge（帶外部電荷控制）) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BQ2011KSN | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Battery Management |
| BQ2011KSN- | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Gas Gauge IC for High Discharge Rates |
| BQ2011KSN-D121 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| BQ2011KSN-N | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Gas Gauge IC for High Discharge Rates |
| BQ2011PN | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Battery Management |
發布緊急采購，3分鐘左右您將得到回復。