- 您現在的位置：買賣IC網 > PDF目錄20583 > ATDH1160VPC- (Atmel)BOARD PROGRAMMING ISP 3V/5V PDF資料下載
參數資料
| 型號： | ATDH1160VPC- |
| 廠商： | Atmel |
| 文件頁數： | 40/54頁 |
| 文件大小： | 0K |
| 描述： | BOARD PROGRAMMING ISP 3V/5V |
| 標準包裝： | 1 |
| 類型： | ISP（系統內可重復編程） |
| 適用于相關產品： | * |
| 所含物品： | 板，線纜，軟件和文檔 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁當前第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁
Troubleshooting
7-4
Atmel ATF15xx Family: ISP Devices User Guide
8.
Problem: The Atmel-ISP software detects the devices in your hardware chain
but reports the wrong number of devices.
Solution: Check whether any device in your JTAG hardware chain was pro-
grammed with a JEDEC file that buffers the TDI pin to the TDO pin. Remove this
device from your circuit board and erase it using an external device programmer.
9.
Problem: The device type you specified in your chain file is incorrect. The
Atmel-ISP software should report this error.
Solution: Make sure to specify the correct device type in the chain file.
10. Problem: Your JTAG hardware chain is incorrectly configured on your circuit
board.
Solution: Your JTAG hardware chain must be hardwired correctly on your circuit
board before you can implement ISP. See also “Setting Up Your Target System” in
Section 5, “Getting Started”, for the correct setup of your JTAG hardware chain.
11. Problem: Your PC’s parallel port is not connected to LPT1 or has the wrong port
address.
Solution: Go to File..Port Setup to change to the correct LPT port setting.
12. Problem: You have specified the correct parallel port address but the ISP soft-
ware still fails to communicate with your circuit board.
Solution: Change your parallel port setting in BIOS to either the ECP or EPP mode.
If you are using Windows 3.x or Windows 95/98, you can also configure Windows
to select the correct ECP or EPP port driver. For details, contact Atmel PLD
Applications.
13. Problem: The ISP software communicates on some PCs but not others. An
earlier version works but the newer version does not.
Solution: Try to use the Self-Calibrate or Manual Calibration options. These options
can be used to slow down the transfer speed the software uses when communicat-
ing between your PC’s parallel port and the hardware. The Atmel-ISP software may
not be able to communicate reliably on some PCs at faster parallel port transfer
speeds. The Self-Calibrate and Manual Calibration options adjust the transfer speed
the software uses so it can reliably communicate between the PC’s parallel port and
your hardware. Older versions of the software communicate at a slower transfer rate
(approximately 50% slower) than newer versions.
14. Problem: You are running the ISP software on Windows NT and the software
fails to communicate with your hardware.
Solution: You need a different version of the ISP software (ATMISPNT) to be able
to run on Windows NT 3.x and above. The Windows NT version of the Atmel-ISP
software is also available on Atmel’s web site and BBS for download.
15. Problem: You have not connected the supply voltage and GND of your target
system to the appropriate VCC and GND pins, respectively, on the 10-pin JTAG
header(s) on your board.
Solution: Wire up the VCC and GND pins on the JTAG header to their respective
VCC and GND buses on your board.
Note:
Contact Atmel PLD Applications if none of the above suggestions appear to
resolve this error.
相關PDF資料 |
PDF描述 |
|---|---|
| T95Z106K035HZAL | CAP TANT 10UF 35V 10% 2910 |
| A7VVB-1510M | CABLE D-SUB-AMU15B/AE15M/AMU15B |
| ISL6613CBZ | IC MOSFET DRVR SYNC BUCK 8-SOIC |
| A7VWB-0910M | CABLE D-SUB-AMU09B/AE09M/AFU09B |
| ISL6613ACBZ | IC MOSFET DRVR SYNC BUCK 8-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ATDH2000 | 功能描述:FPGA DEMONSTRATION BOARD RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 類型:MCU 適用于相關產品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、纜線、軟件、數據表和用戶手冊 其它名稱:520-1035 |
| ATDH2080 | 功能描述:AT6000 SERIES FPGA PROTOTYPE KIT RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 類型:MCU 適用于相關產品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、纜線、軟件、數據表和用戶手冊 其它名稱:520-1035 |
| ATDH2081 | 功能描述:EXTRA DWNLD CABLE ATDH2080 PROBD RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 類型:MCU 適用于相關產品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、纜線、軟件、數據表和用戶手冊 其它名稱:520-1035 |
| ATDH2200E | 功能描述:AT17 CONFIGURATOR PROGRAMMER KIT 制造商:microchip technology 系列:- 零件狀態:在售 類型:系統內編程器 配套使用產品/相關產品:AT17 內容:板，線纜，電源 標準包裝:1 |
| ATDH2200E- | 功能描述:插座和適配器 SERIAL CONFIG MEM. PROG BOARD ENHANCED RoHS:否 制造商:Silicon Labs 產品:Adapter 用于:EM35x |
發布緊急采購，3分鐘左右您將得到回復。