參數資料
型號： ATDH1160VPC-
廠商： Atmel
文件頁數： 32/54頁
文件大?。?/td> 0K
描述： BOARD PROGRAMMING ISP 3V/5V
標準包裝： 1
類型： ISP（系統內可重復編程）
適用于相關產品： *
所含物品： 板，線纜，軟件和文檔
Atmel ATF15xx Family: ISP Devices User Guide
6-1
Section 6
JTAG ISP Guidelines
This section describes important guidelines and information about ISP that all users
must pay attention to when performing ISP operations on Atmel ISP devices.
1.
Make sure all ISP devices on your circuit board are erased before programming.
To prevent the use of the JTAG port pins by any of the ISP devices.
This will enable the JTAG port.
All Atmel ATF15xx devices are shipped in the erased state so that they are ISP-
ready.
2.
Make sure the red LED on the back of the Atmel-ISP cable is on when
programming.
To ensure that the ISP cable is connected properly.
3.
Verify that the correct ISP cable is used.
Atmel-ISP software defaults to using the Atmel-ISP cable.
Must change cable type if using ByteBlaster/ByteBlasterMV cable.
4.
If a parallel cable is used to connect the ISP cable to the PC’s parallel port, make
sure the parallel cable being used is 6 feet long or less.
Parallel cable longer than 6 feet might introduce communication problems
between the ISP cable and the parallel port.
5.
When using Atmel-ISP cable, make sure that the cable is connected to the
ISP\target board before powering up the ISP\target board. Once the ISP\target
board is powered up and the LED on the back of the ISP cable is turned on, then
connect the other side of the ISP cable to the PC’s parallel port.
To eliminate possible communication problem.
6.
Run Self-Calibrate or Manual Calibration if the software is having problems com-
municating with the JTAG device hardware chain.
Self-Calibrate and Manual Calibration allow the user to reduce the transfer
speed of the JTAG signals from the PC’s parallel port to the JTAG device chain.
7.
Make sure your parallel port settings are configured correctly.
The ISP software may have problems running on PCs with Auto mode configu-
ration for parallel port.
Change your BIOS port settings to either ECP or EPP mode.
Confirm your port address setting before using the software.
Default settings are: 0378H for LPT1; 0278H for LPT2.
Other port addresses must be entered manually.
Rev. 1936A-07/01
相關PDF資料
PDF描述
T95Z106K035HZAL CAP TANT 10UF 35V 10% 2910
A7VVB-1510M CABLE D-SUB-AMU15B/AE15M/AMU15B
ISL6613CBZ IC MOSFET DRVR SYNC BUCK 8-SOIC
A7VWB-0910M CABLE D-SUB-AMU09B/AE09M/AFU09B
ISL6613ACBZ IC MOSFET DRVR SYNC BUCK 8-SOIC
相關代理商/技術參數
參數描述
ATDH2000 功能描述:FPGA DEMONSTRATION BOARD RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 類型:MCU 適用于相關產品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、纜線、軟件、數據表和用戶手冊 其它名稱:520-1035
ATDH2080 功能描述:AT6000 SERIES FPGA PROTOTYPE KIT RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 類型:MCU 適用于相關產品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、纜線、軟件、數據表和用戶手冊 其它名稱:520-1035
ATDH2081 功能描述:EXTRA DWNLD CABLE ATDH2080 PROBD RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 類型:MCU 適用于相關產品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、纜線、軟件、數據表和用戶手冊 其它名稱:520-1035
ATDH2200E 功能描述:AT17 CONFIGURATOR PROGRAMMER KIT 制造商:microchip technology 系列:- 零件狀態:在售 類型:系統內編程器 配套使用產品/相關產品:AT17 內容:板，線纜，電源 標準包裝:1
ATDH2200E- 功能描述:插座和適配器 SERIAL CONFIG MEM. PROG BOARD ENHANCED RoHS:否 制造商:Silicon Labs 產品:Adapter 用于:EM35x
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*