- 您現在的位置：買賣IC網 > PDF目錄20583 > ATDH1160VPC- (Atmel)BOARD PROGRAMMING ISP 3V/5V PDF資料下載
參數資料
| 型號： | ATDH1160VPC- |
| 廠商： | Atmel |
| 文件頁數： | 26/54頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD PROGRAMMING ISP 3V/5V |
| 標準包裝： | 1 |
| 類型： | ISP（系統內可重復編程） |
| 適用于相關產品： | * |
| 所含物品： | 板，線纜，軟件和文檔 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁
Atmel ATF15xx Family: ISP Devices User Guide
5-1
Section 5
Getting Started
5.1
In-System
Programming
Procedure
Before you can use the Atmel-ISP software, you will need to make sure that none of the
ISP devices on your circuit board is using the JTAG port pins for logic I/O functions.
Atmel recommends that you erase all devices before inserting them on your circuit
board.
Note:
Atmel ships all ISP devices in a bulk-erased state, which enables the JTAG
interface by default. Therefore, all Atmel devices are initially shipped ISP-ready
and are ready to be programmed with the Atmel-ISP software.
If you are using the Atmel-ISP software with your circuit board, skip the next section and
proceed to “Setting Up Your Target System”.
5.1.1
Setting Up the
Atmel-ISP Board
After completing the instructions in this section, skip the “Setting Up Your Target Sys-
tem” section and proceed to “Running the Atmel-ISP Software”.
1.
Insert an erased Atmel ISP device into the Atmel-ISP board socket. If you are not
sure if a device is erased, erase it on an external device programmer before
inserting it into the ISP board. If you are programming a non-84-pin PLCC
device, you must insert the appropriate daughter board into Socket 2 of the ISP
board and then insert the ISP device into the socket on the daughter board.
2.
Plug an Atmel AC/DC adapter into the 9V DC power connector (J8) on the ISP
board. You can also use a 9V battery to power the ISP board.
3.
Plug the 10-pin female connector on the Atmel-ISP cable to the 10-pin male
header (J5) on the ISP board. Ensure that the 10-pin connector is oriented
correctly.
4.
Power-up the Atmel-ISP board by flipping switch SW3 on the ISP board towards
the power connector. When power is turned on, the ISP board power-on LED
(D3) will be illuminated.
5.
Connect the 25-pin connector on the Atmel-ISP cable to the PC’s parallel port.
Rev. 1936A-07/01
相關PDF資料 |
PDF描述 |
|---|---|
| T95Z106K035HZAL | CAP TANT 10UF 35V 10% 2910 |
| A7VVB-1510M | CABLE D-SUB-AMU15B/AE15M/AMU15B |
| ISL6613CBZ | IC MOSFET DRVR SYNC BUCK 8-SOIC |
| A7VWB-0910M | CABLE D-SUB-AMU09B/AE09M/AFU09B |
| ISL6613ACBZ | IC MOSFET DRVR SYNC BUCK 8-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ATDH2000 | 功能描述:FPGA DEMONSTRATION BOARD RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 類型:MCU 適用于相關產品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、纜線、軟件、數據表和用戶手冊 其它名稱:520-1035 |
| ATDH2080 | 功能描述:AT6000 SERIES FPGA PROTOTYPE KIT RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 類型:MCU 適用于相關產品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、纜線、軟件、數據表和用戶手冊 其它名稱:520-1035 |
| ATDH2081 | 功能描述:EXTRA DWNLD CABLE ATDH2080 PROBD RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 類型:MCU 適用于相關產品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、纜線、軟件、數據表和用戶手冊 其它名稱:520-1035 |
| ATDH2200E | 功能描述:AT17 CONFIGURATOR PROGRAMMER KIT 制造商:microchip technology 系列:- 零件狀態:在售 類型:系統內編程器 配套使用產品/相關產品:AT17 內容:板，線纜，電源 標準包裝:1 |
| ATDH2200E- | 功能描述:插座和適配器 SERIAL CONFIG MEM. PROG BOARD ENHANCED RoHS:否 制造商:Silicon Labs 產品:Adapter 用于:EM35x |
發布緊急采購，3分鐘左右您將得到回復。