- 您現在的位置：買賣IC網 > PDF目錄20583 > ATDH1160VPC- (Atmel)BOARD PROGRAMMING ISP 3V/5V PDF資料下載
參數資料
| 型號： | ATDH1160VPC- |
| 廠商： | Atmel |
| 文件頁數： | 27/54頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD PROGRAMMING ISP 3V/5V |
| 標準包裝： | 1 |
| 類型： | ISP（系統內可重復編程） |
| 適用于相關產品： | * |
| 所含物品： | 板，線纜，軟件和文檔 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁
Getting Started
5-2
Atmel ATF15xx Family: ISP Devices User Guide
5.1.2
Setting Up Your
Target System
Steps 1 and 2 below must be hardwired on your circuit board. These circuit modifica-
tions must be made to your design before you can proceed with any ISP operations.
1.
Make sure all JTAG ISP devices on your circuit board are connected to a 10-pin
male JTAG header. Figure 4-8 on page 4-7 shows the JTAG header pinout. All
JTAG port pins must originate and terminate on this header.
2.
Connect the JTAG port pins (TCK, TDI, TMS, TDO) between the Atmel ISP and
non-Atmel ISP devices together on your circuit board. All JTAG ISP devices must
how to configure single- and multiple-device JTAG chains on your circuit board.
3.
Solder or insert (if you have device sockets) the Atmel ISP devices on your circuit
board. Make sure they are either erased or not programmed with logic that uses
the JTAG port pins for logic I/Os. If the parts are configured in this way, they can-
not be programmed via ISP. Atmel recommends that you solder erased Atmel
ISP devices on your circuit board first since they are ISP-ready when erased. If
you are unsure whether a device is erased, erase it with an external device pro-
grammer before using it in your target system.
4.
Power up your circuit board.
5.
Connect the Atmel-ISP cable from your PC’s parallel port to the 10-pin header
connector on your circuit board. Make sure the 10-pin header connector is ori-
ented correctly on the hardware board, and the LED on the 25-pin connector
housing of the Atmel-ISP cable is illuminated.
6.
You are now ready to run the Atmel-ISP software.
5.1.3
Running the
Atmel-ISP Software
The Atmel-ISP software must be installed on your PC before you can run it. When it is
successfully installed, the Atmel-ISP Program and Help icons are automatically created.
1.
Double-click on the ATMISP icon to start the Atmel-ISP software.
2.
If a chain file has been previously saved, the software will automatically load in
this chain file and the Atmel-ISP main menu will be displayed.
3.
Otherwise, the software will display a dialog box prompting you to enter the num-
ber of devices in you JTAG chain. This will occur immediately after the software
is invoked. Either enter a number or select Cancel. If you select Cancel, the
Atmel-ISP main menu will be displayed and you’ll need to follow the steps below
to create a chain file.
5.1.3.1
Setting Up the
Chain File
1.
From the File menu, click once on New. The software will display a dialog box
prompting you to enter the number of devices in your JTAG chain.
Note:
Step 1 is unnecessary if you followed step 3 above. If you are using ISP soft-
ware with an ISP board, you must select 1 for the number of devices in your
JTAG chain. Selecting a value other than 1 or attempting to program more than
one device on the Atmel-ISP board may cause an error. You can program multi-
ple ISP devices only with a custom target system.
2.
After entering the number of devices, the Device Properties dialog box will
appear. This dialog box will reappear for each device you have defined in your
JTAG chain.
3.
Under Device Type, enter the Atmel ISP device type you want to program.
4.
Under JTAG Instruction, enter the programming operation you want to perform.
Click on the down arrow once for a list of options.
相關PDF資料 |
PDF描述 |
|---|---|
| T95Z106K035HZAL | CAP TANT 10UF 35V 10% 2910 |
| A7VVB-1510M | CABLE D-SUB-AMU15B/AE15M/AMU15B |
| ISL6613CBZ | IC MOSFET DRVR SYNC BUCK 8-SOIC |
| A7VWB-0910M | CABLE D-SUB-AMU09B/AE09M/AFU09B |
| ISL6613ACBZ | IC MOSFET DRVR SYNC BUCK 8-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ATDH2000 | 功能描述:FPGA DEMONSTRATION BOARD RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 類型:MCU 適用于相關產品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、纜線、軟件、數據表和用戶手冊 其它名稱:520-1035 |
| ATDH2080 | 功能描述:AT6000 SERIES FPGA PROTOTYPE KIT RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 類型:MCU 適用于相關產品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、纜線、軟件、數據表和用戶手冊 其它名稱:520-1035 |
| ATDH2081 | 功能描述:EXTRA DWNLD CABLE ATDH2080 PROBD RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 類型:MCU 適用于相關產品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、纜線、軟件、數據表和用戶手冊 其它名稱:520-1035 |
| ATDH2200E | 功能描述:AT17 CONFIGURATOR PROGRAMMER KIT 制造商:microchip technology 系列:- 零件狀態:在售 類型:系統內編程器 配套使用產品/相關產品:AT17 內容:板，線纜，電源 標準包裝:1 |
| ATDH2200E- | 功能描述:插座和適配器 SERIAL CONFIG MEM. PROG BOARD ENHANCED RoHS:否 制造商:Silicon Labs 產品:Adapter 用于:EM35x |
發布緊急采購，3分鐘左右您將得到回復。