參數資料
型號: AT89C51RD2-SLRUM
廠商: Atmel
文件頁數: 3/137頁
文件大小: 0K
描述: IC MCU FLASH 8051 EEP 64K 44PLCC
產品培訓模塊: MCU Product Line Introduction
標準包裝: 1
系列: 89C
核心處理器: 8051
芯體尺寸: 8-位
速度: 60MHz
連通性: SPI,UART/USART
外圍設備: POR,PWM,WDT
輸入/輸出數: 34
程序存儲器容量: 64KB(64K x 8)
程序存儲器類型: 閃存
RAM 容量: 2K x 8
電壓 - 電源 (Vcc/Vdd): 2.7 V ~ 5.5 V
振蕩器型: 外部
工作溫度: -40°C ~ 85°C
封裝/外殼: 44-LCC(J 形引線)
包裝: 標準包裝
配用: AT89OCD-01-ND - USB EMULATOR FOR AT8XC51 MCU
AT89STK-11-ND - KIT STARTER FOR AT89C51RX2
其它名稱: AT89C51RD2-SLRUMDKR
100
4235K–8051–05/08
AT89C51RD2/ED2
24.6.4
Bootloader Functionality
The bootloader can be activated by two means: Hardware conditions or regular boot process.
The Hardware conditions (EA = 1, PSEN = 0) during the Reset# falling edge force the on-chip
bootloader execution. This allows an application to be built that will normally execute the end
user’s code but can be manually forced into default ISP operation.
As PSEN is a an output port in normal operating mode after reset, user application should take
care to release PSEN after falling edge of reset signal. The hardware conditions are sampled at
reset signal falling edge, thus they can be released at any time when reset input is low.
To ensure correct microcontroller startup, the PSEN pin should not be tied to ground during
power-on (See Figure 24-4).
Figure 24-4. Hardware conditions typical sequence during power-on.
The on-chip bootloader boot process is shown Figure 24-5.
VCC
PSEN
RST
Table 24-6.
Bootloader Process Description
Purpose
Hardware Conditions
The Hardware Conditions force the bootloader execution whatever BLJB,
BSB and SBV values.
BLJB
The Boot Loader Jump Bit forces the application execution.
BLJB = 0 => Bootloader execution
BLJB = 1 => Application execution
The BLJB is a fuse bit in the Hardware Byte.
It can be modified by hardware (programmer) or by software (API).
Note: The BLJB test is performed by hardware to prevent any program
execution.
SBV
The Software Boot Vector contains the high address of customer bootloader
stored in the application.
SBV = FCh (default value) if no customer bootloader in user Flash.
Note: The customer bootloader is called by JMP [SBV]00h instruction.
相關PDF資料
PDF描述
VE-23V-IY-F2 CONVERTER MOD DC/DC 5.8V 50W
VE-23V-IY-F1 CONVERTER MOD DC/DC 5.8V 50W
D-621-0424 CONN JACK TRIAXIAL W/SOCKET
5221629-6 CONN TERMINATR PLUG BNC 93OHM AU
VE-23T-IY-F2 CONVERTER MOD DC/DC 6.5V 50W
相關代理商/技術參數
參數描述
AT89C51RD2-SLSIM 功能描述:IC 8051 MCU FLASH 64K 44PLCC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:89C 標準包裝:9 系列:87C 核心處理器:8051 芯體尺寸:8-位 速度:40/20MHz 連通性:UART/USART 外圍設備:POR,WDT 輸入/輸出數:32 程序存儲器容量:32KB(32K x 8) 程序存儲器類型:OTP EEPROM 大小:- RAM 容量:256 x 8 電壓 - 電源 (Vcc/Vdd):4.5 V ~ 5.5 V 數據轉換器:- 振蕩器型:內部 工作溫度:0°C ~ 70°C 封裝/外殼:40-DIP(0.600",15.24mm) 包裝:管件
AT89C51RD2-SLSUM 功能描述:8位微控制器 -MCU 64kB Flash 2048B RAM 2.7V-5.5V RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
AT89C51RD2-SLSUM 制造商:Atmel Corporation 功能描述:IC 8BIT MCU C51/C251 60MHZ 44-PLCC
AT89C51RD2-SMSIM 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Flash Microcontroller
AT89C51RD2-SMSUM 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Flash Microcontroller