- 您現在的位置：買賣IC網 > PDF目錄366549 > Am79C874 (Advanced Micro Devices, Inc.) NetPHY-1LP Low Power 10/100-TX/FX Ethernet Transceiver PDF資料下載
參數資料
| 型號： | Am79C874 |
| 廠商： | Advanced Micro Devices, Inc. |
| 英文描述： | NetPHY-1LP Low Power 10/100-TX/FX Ethernet Transceiver |
| 中文描述： | NetPHY - 1LP低功率10/100-TX/FX以太網收發器 |
| 文件頁數： | 22/60頁 |
| 文件大?。?/td> | 869K |
| 代理商： | AM79C874 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁
22
Am79C874
P R E L I M I N A R Y
10BASE-T Block
The NetPHY-1LP transceiver incorporates the
10BASE-T physical layer functions, including clock re-
covery (ENDEC), MAUs, and transceiver functions.
The NetPHY-1LP transceiver receives 10-Mbps data
from the MAC, switch, or repeater across the MII at 2.5
million nibbles per second (parallel), or 10 million bits
per second (serial). It then Manchester encodes the
data before transmission to the network.
Refer to Figure 4 for the 10BASE-T transmit and re-
ceive data paths.
Figure 4.
10BASE-T Transmit /Receive Data Paths
Twisted Pair Transmit Process
In 10BASE-T mode, Manchester code will be gener-
ated by the 10BASE-T core logic, which will then be
synthesized through the output waveshaping driver.
This will help reduce any EMI emission, eliminating the
need for an external filter. Data transmission over the
10BASE-T medium requires use of the integrated
10BASE-T MAU and uses the differential driver cir-
cuitry on the TX± pins.
TX± is a differential twisted-pair driver. When properly
terminated, TX± meets the transmitter electrical re-
quirements for 10BASE-T transmitters as specified in
IEEE 802.3, Section 14.3.1.2. The load is a twisted pair
cable that meets IEEE 802.3, Section 14.4.
The TX± signal is filtered on the chip to reduce har-
monic content per Section 14.3.2.1 (10BASE-T). Since
filtering is performed in silicon, TX± can be connected
directly to a standard transformer. External filtering
modules are not needed
Twisted Pair Receive Process
In 10BASE-T mode, the signal first passes through a
third order Elliptical filter, which filters all the noise from
the cable, board, and transformer. This eliminates the
need for a 10BASE-T external filter. A Manchester de-
coder and a Serial-to-Parallel converter then follow to
generate the 4-bit nibble in MII mode.
RX+ ports are differential twisted-pair receivers. When
properly terminated, each RX+ port meets the electri-
cal requirements for 10BASE-T receivers as specified
in IEEE 802.3, Section 14.3.1.3. Each receiver has in-
ternal filtering and does not require external filter mod-
ules or common mode chokes.
Signals appearing at the RX± differential input pair are
routed to the internal decoder. The receiver function
meets the propagation delays and jitter requirements
specified by the 10BASE-T standard. The receiver
squelch level drops to half its threshold value after un-
squelch to allow reception of minimum amplitude sig-
nals and to mitigate carrier fade in the event of worst
case signal attenuation and crosstalk noise conditions.
Twisted Pair Interface Status
The NetPHY-1LP transceiver will power up in the Link
Fail state. The Auto-Negotiation algorithm will apply to
allow it to enter the Link Pass state. A link-pulse detec-
tion circuit constantly monitors the RX± pins for the
presence of valid link pulses. In the Link Pass state, re-
ceive activity which passes the pulse width/amplitude
requirements of the RX± inputs cause the PCS Control
block to assert Carrier Sense (CRS) signal at the MII
interface.
Collision Detect Function
Simultaneous activity (presence of valid data signals)
from both the internal encoder transmit function and
the twisted pair RX± pins constitutes a collision,
thereby causing the PCS Control block to assert the
COL pin at the MII.
Collisions cause the PCS Control block to assert the
Carrier Sense (CRS) and Collision (COL) signals at the
MII. In the Link Fail state, this block would cause the
PCS Control block to de-assert Carrier Sense (CRS)
and Collision (COL).
Jabber Function
The Jabber function inhibits the 10BASE-T twisted pair
transmit function of the NetPHY-1LP transceiver device
if the TX± circuits are active for an excessive period
(20-150 ms). This prevents one port from disrupting the
network due to a
stuck-on
or faulty transmitter condi-
tion. If the maximum transmit time is exceeded, the
data path through the 10BASE-T transmitter circuitry is
disabled (although Link Test pulses will continue to be
Clock
Data
Manchester
Encoder
Clock
Data
Manchester
Decoder
Squelch
Circuit
RX Driver
RX
±
TX
±
TX Driver
Loopback
(Register 0)
22235I-6
相關PDF資料 |
PDF描述 |
|---|---|
| AM79C874VC | NetPHY-1LP Low Power 10/100-TX/FX Ethernet Transceiver |
| AM79C875 | NetPHY⑩ 4LP Low Power Quad 10/100-TX/FX Ethernet Transceiver |
| AM79C875KC | NetPHY⑩ 4LP Low Power Quad 10/100-TX/FX Ethernet Transceiver |
| AM79C875KI | NetPHY⑩ 4LP Low Power Quad 10/100-TX/FX Ethernet Transceiver |
| AM79C901AJC | HomePHY Single-Chip 1/10 Mbps Home Networking PHY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM79C874KC/W | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LAN Transceiver |
| AM79C874VC | 制造商:Advanced Micro Devices 功能描述:PHY 1-CH 10Mbps/100Mbps 80-Pin TQFP 制造商:AMD (Advanced Micro Devices) 功能描述:PHY 1-CH 10Mbps/100Mbps 80-Pin TQFP |
| AM79C874VD | 制造商:Advanced Micro Devices 功能描述:PHY 1-CH 10Mbps/100Mbps 80-Pin TQFP 制造商:AMD (Advanced Micro Devices) 功能描述:PHY 1-CH 10Mbps/100Mbps 80-Pin TQFP |
| AM79C874VF | 制造商:Advanced Micro Devices 功能描述:PHY 1-CH 10Mbps/100Mbps 80-Pin TQFP 制造商:AMD (Advanced Micro Devices) 功能描述:PHY 1-CH 10Mbps/100Mbps 80-Pin TQFP |
發布緊急采購，3分鐘左右您將得到回復。