- 您現在的位置：買賣IC網 > PDF目錄366549 > AM79C30AJC (ADVANCED MICRO DEVICES INC) Digital Subscriber Controller⑩ (DSC⑩) Circuit PDF資料下載
參數資料
| 型號： | AM79C30AJC |
| 廠商： | ADVANCED MICRO DEVICES INC |
| 元件分類： | 數字傳輸電路 |
| 英文描述： | Digital Subscriber Controller⑩ (DSC⑩) Circuit |
| 中文描述： | DATACOM, DIGITAL SLIC, PQCC44 |
| 封裝： | PLASTIC, LCC-44 |
| 文件頁數： | 11/101頁 |
| 文件大小： | 1607K |
| 代理商： | AM79C30AJC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁
Am79C30A/32A Data Sheet
11
Bc buffers must be accessed within 122.4 μs. This is to
prevent erroneous data transfers. Only one interrupt is
used to signal accessibility for both B channels of the S
Interface. Since the data transfer must occur synchro-
nously to the S Interface, any data access to either Bb
or Bc or both must be made within the122.4 μs limit.
Note that even though only a single interrupt is issued,
either or both S-Interface B channels must be serviced.
IR bits 2, 3, 5, 6, and 7, if set, indicate that a bit has
been set in the associated status or error register. All of
the interrupts generated by the Am79C30A/32A can be
individually disabled. In the case of IR bit 7, the inter-
rupt can also be masked by setting PPIER bit 7 to 0.
DMR1, DMR2, DMR3, LMR2, MCR4, and MF control
the mask conditions that affect the INT pin. The INT pin
is activated only by interrupts that are not disabled. The
Interrupt Register reflects the status of enabled inter-
rupts. The INT pin can be disabled by setting INIT Reg-
ister bit 2 to a logical 1.
The Am79C30A/32A has facilities that allow the micro-
processor to read the status registers (status update is
inhibited during status read) or the IR at any time dur-
ing functional operation.
相關PDF資料 |
PDF描述 |
|---|---|
| AM79C30AVC | Digital Subscriber Controller⑩ (DSC⑩) Circuit |
| AM79C32A | Digital Subscriber Controller⑩ (DSC⑩) Circuit |
| AM79C32AJC | Digital Subscriber Controller⑩ (DSC⑩) Circuit |
| AM79C32AVC | Digital Subscriber Controller⑩ (DSC⑩) Circuit |
| AM79C850KC | SUPERNET-R 3 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM79C30AJC/D | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| AM79C30AJC/DTR | 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel |
| AM79C30AJC/E | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| AM79C30AJC/E3 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| AM79C30AJC/E4 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
發布緊急采購，3分鐘左右您將得到回復。