
[AK4673] 
MS0670-E-00 
2007/09 
- 5 - 
PIN/FUNCTION 
No. Pin Name 
I/O 
Function 
A1 NC 
- 
No Connection pin 
No internal bonding. This pin should be connected to ground (VSS1, VSS2 or VSS3 pin).
MIC Power Supply Pin 
Common Voltage Output Pin, 0.45 x AVDD 
Bias voltage of ADC inputs and DAC outputs. 
Ground 1 Pin 
Analog Power Supply Pin, 2.6 ~ 3.6V 
Output Pin for Loop Filter of PLL Circuit (AIN3 bit = “0”: PLL is available.) 
This pin should be connected to VSS1 with one resistor and capacitor in series. 
Rch Analog Input 3 Pin (AIN3 bit = “1”: PLL is not available.) 
No Connection pin 
No internal bonding. This pin should be connected to ground (VSS1, VSS2 or VSS3 pin).
I
2
C Control Mode Pin. This pin should be tied to AVDD.  
Power-Down Mode Pin (This pin is valid only for the Audio Block) 
“H”: Power-up, “L”: Power-down 
This pin does not apply to a power down and a reset for the TSC block and TSC related 
registers. Power-down on the TSC block is determined by the PD0 bit shown in 
Table 61
. 
Audio Block I
2
C bus Slave Address (CADA) bit  Select Pin  
Audio Block Control Data Clock Pin.   
No Connection pin 
No internal bonding. This pin should be connected to ground (VSS1, VSS2 or VSS3 pin).
I/O Audio Block Control Data Input Pin.  
I 
Audio Serial Data Input Pin 
O 
Audio Serial Data Output Pin 
I/O Input / Output Channel Clock Pin 
I/O Audio Serial Data Clock Pin 
No Connection pin 
No internal bonding. This pin should be connected to ground (VSS1, VSS2 or VSS3 pin).
- 
Digital Power Supply Pin, 2.6 ~ 3.6V 
No Connection pin 
No internal bonding. This pin should be connected to ground (VSS1, VSS2 or VSS3 pin).
- 
Digital I/O Power Supply Pin (Audio Stream), 1.6 ~ 3.6V 
Digital I/O Power Supply Pin (uP I/F), 2.5 ~ 3.6V 
This pin should be connected to TSVDD pin. 
No Connection pin 
No internal bonding. This pin should be connected to ground (VSS1, VSS2 or VSS3 pin).
I 
External Master Clock Input Pin 
No Connection pin 
No internal bonding. This pin should be connected to ground (VSS1, VSS2 or VSS3 pin).
No Connection pin 
No internal bonding. This pin should be connected to ground (VSS1, VSS2 or VSS3 pin).
O 
Master Clock Output Pin 
No Connection pin 
No internal bonding. This pin should be connected to ground (VSS1, VSS2 or VSS3 pin).
- 
Ground 2 Pin 
- 
Headphone Amp Power Supply Pin, 2.6 ~ 5.25V 
O 
Rch Headphone-Amp Output Pin 
O 
Lch Headphone-Amp Output Pin 
No Connection pin 
No internal bonding. This pin should be connected to ground (VSS1, VSS2 or VSS3 pin).
Mute Time Constant Control Pin 
Connected to VSS2 pin with a capacitor for mute time constant. 
C2 
MPWR 
O 
A2 VCOM 
O 
B1 
C1 
VSS1 
AVDD 
- 
- 
VCOC 
O 
E2 
RIN3 
I 
F2 
NC 
- 
D2 I2CA 
I 
G2 PDN 
I 
H1 CADA 
H2 SCLA 
I 
I 
J1 
NC 
- 
J2 
H3 SDTI 
J3 
SDTO 
H4 LRCK 
J4 
BICK 
SDAA 
H5 NC 
- 
J6 
DVDD 
H7 NC 
- 
H6 TVDD2 
J7 
TVDD1 
- 
J8 
NC 
- 
H9 MCKI 
G8 NC 
- 
G9 NC 
- 
H8 MCKO 
J9 
NC 
- 
D8 VSS2 
D9 HVDD 
C8 
HPR 
C9 
HPL 
B8 
NC 
- 
B9 
MUTET 
O