- 您現在的位置：買賣IC網 > PDF目錄385093 > AK4560AVQ (Asahi Kasei Microsystems Co.,Ltd) 16bit CODEC with ALC and MIC/HP/SPK-Amps PDF資料下載
參數資料
| 型號： | AK4560AVQ |
| 廠商： | Asahi Kasei Microsystems Co.,Ltd |
| 元件分類： | Codec |
| 英文描述： | 16bit CODEC with ALC and MIC/HP/SPK-Amps |
| 中文描述： | 16位編解碼器ALC和麥克風/惠普/胰腎聯合移植，放大器 |
| 文件頁數： | 41/47頁 |
| 文件大?。?/td> | 339K |
| 代理商： | AK4560AVQ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁當前第41頁第42頁第43頁第44頁第45頁第46頁第47頁
ASAHI KASEI
[AK4560A]
MS0028-E-00
2000/05
- 41 -
2. ALC1 Recovery Operation
The ALC1 recovery operation waits until a time of setting WTM1-0 bits after completing the ALC1 limiter. If the input
signal does not exceed “LMTH – 2dB”, the ALC1 recovery operation is done. The IPGA value increases automatically by
this operation up to the set reference level (REF6-0 bits). Then the IPGA value is set for L/R commonly. The ALC1
recovery operation is done at a period set by WTM1-0 bits.
When L/R channels are detected by zero crossing operation during WTM1-0, the ALC1 recovery operation waits until
WTM1-0 period and the next recovery operation is done.
During the ALC1 recovery operation, when either input signal level of Lch or Rch exceeds the ALC1 limiter detection
level (LNTH), the ALC1 recovery operation changes into the ALC1 limiter operation immediately
In case of “(Recovery waiting counter reset level)
≤
Input Signal < Limiter detection level” during the ALC1 recovery
operation, the waiting timer of ALC1 recovery operation is reset. Therefore, in case of “(Recovery waiting counter reset
level) > Input Signal”, the waiting timer of ALC1 recovery operation starts.
During recovery counter reset
Limiter detection level (LMTH)
Recovery waiting counter
reset level (LMTH)
Zero crossing detect
WTM counter starts
WTM counter starts
WTM counter starts
ZTM counter starts
ZTM counter starts
(1)
(2)
(2)
WTM counter starts
(2)
Figure 32. The transition from the limiter operation to the recovery operation
(1). When the input signal is below the ALC1 recovery waiting counter reset level, the ALC1 recovery operation waits the
time set by WTM1-0 bits. If the input signal does not exceed the ALC1 limiter detection level or the ALC1 recovery
waiting counter reset level, the ALC1 recovery operation is done only once.
(2). The IPGA value is changed by the zero crossing operation in ALC1 recovery operation, but the next counter of the
ALC1 recovery waiting timer is also starting.
Other:
When a channel of one side enters the limiter operation during the waiting zero crossing, the present ALC1 recovery
operation stops, according as the small value of IPGA (a channel of waiting zero crossing), the ALC1 limiter operation is
done.
When both channels are waiting for the next ALC1 recovery operation, the ALC1 limiter operation is done from the IPGA
value of a point in time.
During the ALC1 operation, the value of writing in IPGA6-0 bits is ignored.
相關PDF資料 |
PDF描述 |
|---|---|
| AK4561 | 16bit CODEC with built-in ALC and MIC/HP-Amp |
| AK4561VQ | 16bit CODEC with built-in ALC and MIC/HP-Amp |
| AK4562 | LOW POWER 20BIT CODEC WITH PGA |
| AK4562VN | LOW POWER 20BIT CODEC WITH PGA |
| AK4563A | Low Power 16bit 4ch ADC & 2ch DAC with ALC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AK4561 | 制造商:AKM 制造商全稱:AKM 功能描述:16bit CODEC with built-in ALC and MIC/HP-Amp |
| AK4561VQ | 制造商:AKM 制造商全稱:AKM 功能描述:16bit CODEC with built-in ALC and MIC/HP-Amp |
| AK4562 | 制造商:AKM 制造商全稱:AKM 功能描述:EVALUATION BOARD REV.A FOR AK4562 |
| AK4562VN | 制造商:AKM 制造商全稱:AKM 功能描述:LOW POWER 20BIT CODEC WITH PGA |
| AK4563A | 制造商:AKM 制造商全稱:AKM 功能描述:Low Power 16bit 4ch ADC & 2ch DAC with ALC |
發布緊急采購，3分鐘左右您將得到回復。