- 您現在的位置：買賣IC網 > PDF目錄385089 > AK2570 (Asahi Kasei Microsystems Co.,Ltd) Feed Forward APC LSI for LD Module PDF資料下載
參數資料
| 型號： | AK2570 |
| 廠商： | Asahi Kasei Microsystems Co.,Ltd |
| 英文描述： | Feed Forward APC LSI for LD Module |
| 中文描述： | 前饋apc的大規模集成電路模塊為勞工處 |
| 文件頁數： | 7/27頁 |
| 文件大?。?/td> | 292K |
| 代理商： | AK2570 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
ASAHI KASEI
[AK2570]
<MS0115-E-00>
2001/10
7
(2) Training mode
“
Training mode
”
is used for the evaluation and the adjustment about AK2570. It is possible to write and read
the data in the EERPOM and the registers and to execute activating the internal circuit for setting the
temperature compensation data with the serial interface. Notice that it is possible to shift to
“
Training mode
”
by executing
‘
Command for Training mode
’
and any other command is not available while operating in
“
Self-operation mode
”
.
After executing
‘
Command for Training mode
’
, it is necessary to input the clock or the
‘
H
’
level signal to
SK-pin continuously to keep the operational mode is in
“
Training mode
“
. It is able to return to
“
Self-
operational mode
”
by forcing the
‘
L
’
level signal to SK-pin for 50msec more in
“
Training mode
”
.
In
“
Training mode
”
, the periodical operation of temperature compensation for the LD is stopped. Also at the
time of executing
‘
Command for Training mode
’
while operating in
“
Self-operational mode
”
, AK2570
transfers to
“
Training mode
”
after completing the periodical operation.
Recommended sequence in
”
Training mode
START
Set the temperature at the minimum value for the use (e.g. -40
℃
)
Execute 'Command for Training mode'
Write '00000' in RINT register
AD2 executes A to D conversion
for the T-SENSE output
Confirm the code generated by AD2
is '00000010'~'00001000' (e.g. -40
℃
)
Add '+1' to the data
in RINT register
N
ｏ
Set the data for DA1 & DA2 that will be retained in
EDA1 &EDA2 to fit the LD characteristics
After execting the A to D conversion in AD1 for
the input voltage to VPDIN-pin, read the data in
Complete the measurement for the compensation data
Make the data for writing in the EEPROM
Write the compensatory data in the EEPROM
FINISH
Change the
ambient temperature
--> Register access :
READ-REG(RTMP)
Y
ｅｓ
Y
ｅｓ
N
ｏ
--> Initial setting : Command for Training mode
--> Register access : WRITE-REG(RINT)
--> Initial Setting : Command for Selecting AD2
--> Activating Internal Circuit :
Command for A/D operation
--> Register Access : READ-REG(RTMP)
--> Register access
WRITE-REG(RINT)
--> Register Access : WRITE-REG(RDA1)
--> Register Access : WRITE-REG(RDA2)
--> Evaluation for the LD characteristics
--> Register Access : READ-REG(RVPD)
--> EEPROM Access : WRITE-EEP
--> EEPROM Access : EWEN
--> Adjusting the monitoring PD
--> Initial Setting : Command for Selecting AD1
--> Activating Internal Circuit :
Command for A/D operation
RVPD register that will be retained in EDA3
(See p.15)
相關PDF資料 |
PDF描述 |
|---|---|
| AK2572 | APC for Burst Mode Applicable Direct Modulation Laser Diode |
| AK2573A | 125M / 156M Laser Diode Driver + APC |
| AK2573AVB | 125M / 156M Laser Diode Driver + APC |
| AK2574 | 156M Laser Diode Driver + APC for Burst Mode |
| AK2574VB | 156M Laser Diode Driver + APC for Burst Mode |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AK2571 | 制造商:AKM 制造商全稱:AKM 功能描述:Single-Chip Automatic Power/Temperature Control for WDM Laser Diodes |
| AK2572 | 制造商:AKM 制造商全稱:AKM 功能描述:APC for Burst Mode Applicable Direct Modulation Laser Diode |
| AK2573A | 制造商:AKM 制造商全稱:AKM 功能描述:125M / 156M Laser Diode Driver + APC |
| AK2573AVB | 制造商:AKM 制造商全稱:AKM 功能描述:125M / 156M Laser Diode Driver + APC |
| AK2574 | 制造商:AKM 制造商全稱:AKM 功能描述:156M Laser Diode Driver + APC for Burst Mode |
發布緊急采購，3分鐘左右您將得到回復。