- 您現在的位置：買賣IC網 > PDF目錄385089 > AK2570 (Asahi Kasei Microsystems Co.,Ltd) Feed Forward APC LSI for LD Module PDF資料下載
參數資料
| 型號： | AK2570 |
| 廠商： | Asahi Kasei Microsystems Co.,Ltd |
| 英文描述： | Feed Forward APC LSI for LD Module |
| 中文描述： | 前饋apc的大規模集成電路模塊為勞工處 |
| 文件頁數： | 6/27頁 |
| 文件大?。?/td> | 292K |
| 代理商： | AK2570 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
ASAHI KASEI
[AK2570]
<MS0115-E-00>
2001/10
6
[b] Explanation for the modes and the commands
(1) Self-operation mode
The on-chip
‘
Power on Reset
’
circuit initializes the data in all registers and sets AK2570 in
“
Self-operation
mode
”
automatically at
‘
Power ON
’
. In
“
Self-operation mode
”
, AK2570 operates as below and keeps the
emission intensity of the LD module constant by periodically applying the compensation voltage for the Bias-
and the Modulation- current against the temperature drift of the LD module.
In 50msec after the end of the resetting operation at
‘
Power ON
’
, the data in EEPROM (Address =
‘
1 1111 1111
[EINT memory]
’
) is transferred to RINT and RATRM registers. Notice that the data in these registers can not
change except the case of executing
‘
Power ON
’
again or re-writing the data with executing
‘
WRITE-REG
’
command in
“
Training mode
’
.
In
“
Self-operation mode
”
, the T-SENSE converts the detected ambient temperature to the voltage. AD2
encodes this voltage to the 8bits digital data and transfers this data to RTMP register. This data is converted to
the EEPROM address and utilized for reading the temperature characteristic data of the LD retained in the
EEPROM. The EEPROM data is transferred to RDA1 ~ RDA3 registers and the output voltage of DA1 ~ DA3
are controlled. It is realized that the constant emission intensity of the LD is independent with the temperature
drift by controlling the Bias- and the Modulation- current for the LD module and the alarm signal for the
weakened LD. This behavior is executed periodically (the period is about 100ms). While operating in
“
Self-operation mode
”
, it is impossible to execute any command except
‘
Command for Training mode
’
.
Note) REG0 register : This register synsthesizes the 32bits data and temporarily holds the data
when transferring the data from the EEPROM to the registers.
Power ON
The 'Power on Reset' circuit operates and initializes the data in all registers.
The data for RINT & RATRM registers retained in EEPROM (Address="1 1111 1111") is transferred to REG0 register.
The data is transferred from REG0 register to RINT & RATRM registers.
AD2 executes A to D conversion for the output voltage from the T-SENSE.
The access to EEPROM is executed with referring the data held in RTMP register.
The data for RDA1~2 registers retained in EEPROM (address = "x xxxx xxx0")
is transferred to D31~D16 in REG0 register.
The data for RDA3 register retained in EEPROM (address = "x xxxx xxx1") is
transferred to D15~D8 in REG0 register.
The data in REG0 register is transferred to RDA1 ~ RDA3 registers.
It is waiting for the next compensatory operation.
0.6ms
（
typ
）
50ms
（
typ
）
The period is
about 100ms
The output data "XXXX XXXX" generated by AD2 is transferred to RTMP register.
相關PDF資料 |
PDF描述 |
|---|---|
| AK2572 | APC for Burst Mode Applicable Direct Modulation Laser Diode |
| AK2573A | 125M / 156M Laser Diode Driver + APC |
| AK2573AVB | 125M / 156M Laser Diode Driver + APC |
| AK2574 | 156M Laser Diode Driver + APC for Burst Mode |
| AK2574VB | 156M Laser Diode Driver + APC for Burst Mode |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AK2571 | 制造商:AKM 制造商全稱:AKM 功能描述:Single-Chip Automatic Power/Temperature Control for WDM Laser Diodes |
| AK2572 | 制造商:AKM 制造商全稱:AKM 功能描述:APC for Burst Mode Applicable Direct Modulation Laser Diode |
| AK2573A | 制造商:AKM 制造商全稱:AKM 功能描述:125M / 156M Laser Diode Driver + APC |
| AK2573AVB | 制造商:AKM 制造商全稱:AKM 功能描述:125M / 156M Laser Diode Driver + APC |
| AK2574 | 制造商:AKM 制造商全稱:AKM 功能描述:156M Laser Diode Driver + APC for Burst Mode |
發布緊急采購，3分鐘左右您將得到回復。