- 您現在的位置：買賣IC網 > PDF目錄385089 > AK2570 (Asahi Kasei Microsystems Co.,Ltd) Feed Forward APC LSI for LD Module PDF資料下載
參數資料
| 型號： | AK2570 |
| 廠商： | Asahi Kasei Microsystems Co.,Ltd |
| 英文描述： | Feed Forward APC LSI for LD Module |
| 中文描述： | 前饋apc的大規模集成電路模塊為勞工處 |
| 文件頁數： | 3/27頁 |
| 文件大?。?/td> | 292K |
| 代理商： | AK2570 |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
ASAHI KASEI
[AK2570]
<MS0115-E-00>
2001/10
3
AK2570 consists of these circuit blocks as below.
Circuit block
This circuit generates the standard clock that settles the timing for the sequence of the
internal circuit in
“
Self-operation mode (Ordinary mode)
”
.
This circuit generates the reference voltage for the A to D converter, the D to A converter
and the T-SENSE.
This circuit is the thermo-sensor, outputs the voltage corresponding to the ambient
temperature, i.e. the temperature to voltage converter, and transfers this output voltage to
AD2. Also it integrates the offset adjustment circuit that cancels the distribution.
The A to D converter encodes the input voltage at VPDIN-pin (the signal from the
monitor PD) to the 8bits digital data. It is possible to read the encoded data of monitor PD
signal (the reference data for RDA3) held in RVPD register and to set the alarm threshold
level for the degraded LD in
“
Training mode
”
.
The A to D converter encodes the T-SENSE output signal to the 8bits digital data. In
“
Self- operation mode
”
, the encoded data of the ambient temperature detected by the
T-SENSE is converted to the EEPROM address and utilized for reading the temperature
characteristic data of the LD retained in the EEPROM. In
“
Training mode
”
, it is possible
to read the encoded data of the detected temperature held in RTMP register.
This block consists of the D to A converter and the Op-amp and controls the Bias- or the
Modulation- current for the LD. DA1 decodes the 8bits digital data held in RDA1 register
to the compensation voltage for the temperature drift of the LD. Inputting the
‘
H
’
level
signal to SHUTDN-pin makes that DAOUT1-pin outputs
‘
0V (min.)
’
.
This block consists of the D to A converter and the Op-amp and controls the Bias- or the
Modulation- current for the LD. DA2 decodes the 8bits digital data held in RDA2 register
to the compensation voltage for the temperature drift of the LD. Inputting the
‘
H
’
level
signal to SHUTDN-pin makes that DAOUT2-pin outputs
‘
0V (min.)
’
.
DA3, ALMOUT,
Comparator, ALM
Timing Generator
EEPROM and held in RDA3 register, and this case is caused by the aging degradation.
This memory is the non-volatile memory, has the capacity
‘
Address 9bits
×
Data 16bits
’
and retains the data as below,
1. The temperature compensation data for the LD (transferred to RDA1 and RDA2 registers)
and the alarm threshold level data for the degraded LD (transferred to RDA3 register)
corresponding to the ambient temperature (the output from the T-SNESE and AD2).
2. The trimming data for the T-SENSE offset and the ALMOUT timing.
This circuit temporarily stores the ambient temperature data (in RTMP register), the
temperature compensation data for the LD (in RDA1 and RDA2 registers), the alarm
threshold level data (in RDA3 register) and so on.
Control
This circuit controls the internal circuit, e.g. registers, with the serial interface.
At
‘
Power ON
’
, this circuit initializes the data in all registers (see p.9) and sets AK2570 in
“
Self-operation mode
”
.
Functional description
Oscillator
VREF
T-SENSE
AD1
AD2
DA1,
AMP1
DA2,
AMP2
This block outputs the
‘
H
’
level alarm signal from ALM-pin in the case that the
monitoring PD signal becomes lower than the alarm threshold level retained in the
EEPROM
Register
Power on Reset
相關PDF資料 |
PDF描述 |
|---|---|
| AK2572 | APC for Burst Mode Applicable Direct Modulation Laser Diode |
| AK2573A | 125M / 156M Laser Diode Driver + APC |
| AK2573AVB | 125M / 156M Laser Diode Driver + APC |
| AK2574 | 156M Laser Diode Driver + APC for Burst Mode |
| AK2574VB | 156M Laser Diode Driver + APC for Burst Mode |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AK2571 | 制造商:AKM 制造商全稱:AKM 功能描述:Single-Chip Automatic Power/Temperature Control for WDM Laser Diodes |
| AK2572 | 制造商:AKM 制造商全稱:AKM 功能描述:APC for Burst Mode Applicable Direct Modulation Laser Diode |
| AK2573A | 制造商:AKM 制造商全稱:AKM 功能描述:125M / 156M Laser Diode Driver + APC |
| AK2573AVB | 制造商:AKM 制造商全稱:AKM 功能描述:125M / 156M Laser Diode Driver + APC |
| AK2574 | 制造商:AKM 制造商全稱:AKM 功能描述:156M Laser Diode Driver + APC for Burst Mode |
發布緊急采購，3分鐘左右您將得到回復。