參數資料
型號： ADV7183KST
廠商： ANALOG DEVICES INC
元件分類： 顏色信號轉換
英文描述： Advanced Video Decoder with 10-Bit ADC and Component Input Support
中文描述： COLOR SIGNAL DECODER, PQFP80
封裝： PLASTIC, LQFP-80
文件頁數： 10/41頁
文件大小： 484K
代理商： ADV7183KST
REV. 0
–10–
ADV7183
In S-video mode there are two clamp controllers used to sepa-
rately control the luminance clamping and the chrominance
clamping. Also in YCrCb component input mode there are two
clamp controllers used to control the luminance clamping and
the CrCb clamping separately; there are, however, individual
current clamps on the Cr and Cb inputs.
User programmability is built into the clamp controllers which
enable the current and digital clamp controllers to be set up to
user-defined conditions. Refer to analog clamp control register
(14H), digital clamp control register (15H), and digital color
clamp offset register (15H and 16H) for control settings.
ANALOG-TO-DIGITAL CONVERTERS
Two 10-bit ADCs are used in the ADV7183, and they run from
a 27 MHz input clock. An integrated band gap generates the
required reference voltages for the converters. If the decoder is
configured in CVBS mode, the second ADC can be switched off
to reduce power consumption, see PSC[1:0].
AUTOMATIC GAIN CONTROL
The AGC control block on the ADV7183 is a digitally based
system. This controller ensures that the input video signal
(CVBS, S-video, or YCrCb) is scaled to its correct value such
that the YCrCb digital output data matches the correct gain of
the video signal. The AGC has an analog input video range of
0.5 V p-p to 2.0 V p-p, which gives a –6 dB to +6 dB gain range.
Figure 6 demonstrates this range. This AGC range will compensate
for video signals that have been incorrectly terminated or have
been attenuated due to cable loss or other factors.
There are two main control blocks: one for the luminance chan-
nel and one for the chrominance channel.
The luminance automatic gain control has eight modes of
operation:
1. Manual AGC mode where gain for the luminance path is set
manually using LGM[11:0].
2. Blank level to sync tip is used to set the luminance gain;
manual MIRE[2:0] controls the maximum value through the
luminance channel. There is no override of this mode when
white peak mode is detected.
3. Blank level to sync tip is used to set luminance gain; manual
MIRE[2:0] controls the maximum value through luminance
channel. There is override of this mode when white peak
mode is detected. White peak mode is activated when the
input video exceeds the maximum luminance range for long
periods; this mode is designed to prevent clipping of the
input video signal.
4. Blank level to sync tip is used to set luminance gain;
MIRE[2:0] is automatically controlled to set the maximum
value through the luminance channel. There is no override
of this mode when white peak mode is detected.
5. Blank level to sync tip is used to set luminance gain; manual
MIRE[2:0] is automatically controlled to set the maximum
value through the luminance channel. There is override of
this mode when white peak mode is detected. White peak
mode is activated when the input video exceeds the maxi-
mum luminance range for long periods; this mode is designed
to prevent clipping of the input video signal.
6.
Based on active video peak white. PW_UPD sets the gain
update
frequency (once per field).
7.
Based on average active video. PW_RES sets what lines are used;
only relevant if the signal conforms to PAL 625 line standard.
8. The luminance channel gain is frozen at its present value.
6
A
–
0
–
6
C
–
0
RANGE = 12dB
MAXIMUM
MINIMUM
Figure 6. Analog Input Range
The chrominance automatic gain control has four modes of
operation:
1. Manual AGC mode where gain for chrominance path is set
manually using CGM[11:0].
2. Luminance gain used for chrominance channel.
3. Chrominance automatic gain based on color burst amplitude.
4. Chrominance gain frozen at its present setting.
Both the luminance and chrominance AGC controllers have a
programmable time constant that allows the AGC to operate in
four modes: slow, medium, fast, and video quality controlled.
The maximum IRE (MIRE[2:0]) control can be used to set the
maximum input video range that can be decoded. Table I shows
the selectable range.
Table I. MIRE Control
Function
MIRE[2:0]
PAL (IRE)
NTSC (IRE)
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
133
125
120
115
110
105
100
100
122
115
110
105
100
100
100
100
相關PDF資料
PDF描述
AD7183 Advanced Video Decoder with 10-Bit ADC and Component Input Support
ADV7185 Professional NTSC/PAL Video Decoder with 10-Bit CCIR656 Output
ADV7185KST Professional NTSC/PAL Video Decoder with 10-Bit CCIR656 Output
ADV7190KST Video Encoder with Six 10-Bit DACs and Video Encoder with Six DAC Outputs
ADV7191 Video Encoder with Six 10-Bit DACs and Video Encoder with Six DAC Outputs
相關代理商/技術參數
參數描述
ADV7184 制造商:AD 制造商全稱:Analog Devices 功能描述:Multiformat SDTV Video Decoder with Fast Switch Overlay Support
ADV7184BSTZ 功能描述:IC DECODER VID SDTV MULTI 80LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 編碼器，解碼器，轉換器 系列:- 產品變化通告:Development Systems Discontinuation 26/Apr/2011 標準包裝:1 系列:- 類型:編碼器 應用:DVB-S.2 系統 電壓 - 電源，模擬:- 電壓 - 電源，數字:- 安裝類型:- 封裝/外殼:模塊 供應商設備封裝:模塊 包裝:散裝 其它名稱:Q4645799
ADV7185 制造商:AD 制造商全稱:Analog Devices 功能描述:Professional NTSC/PAL Video Decoder with 10-Bit CCIR656 Output
ADV7185KST 制造商:AD 制造商全稱:Analog Devices 功能描述:Professional NTSC/PAL Video Decoder with 10-Bit CCIR656 Output
ADV7186 制造商:AD 制造商全稱:Analog Devices 功能描述:Video Decoder and Display Processor
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*