參數資料
型號： ADUC816BSZ
廠商： Analog Devices Inc
文件頁數： 54/68頁
文件大?。?/td> 0K
描述： IC MCU 8K FLASH ADC/DAC 52MQFP
產品培訓模塊： Process Control
標準包裝： 1
系列： MicroConverter® ADuC8xx
核心處理器： 8052
芯體尺寸： 8-位
速度： 12.58MHz
連通性： I²C，SPI，UART/USART
外圍設備： PSM，溫度傳感器，WDT
輸入/輸出數： 34
程序存儲器容量： 8KB（8K x 8）
程序存儲器類型： 閃存
EEPROM 大小： 640 x 8
RAM 容量： 256 x 8
電壓 - 電源 (Vcc/Vdd)： 2.7 V ~ 5.5 V
數據轉換器： A/D 7x16b; D/A 1x12b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 52-QFP
包裝： 托盤
產品目錄頁面： 738 (CN2011-ZH PDF)
REV. 0
ADuC816
–58–
Mode 0: 8-Bit Shift Register Mode
Mode 0 is selected by clearing both the SM0 and SM1 bits in
the SFR SCON. Serial data enters and exits through RXD. TXD
outputs the shift clock. Eight data bits are transmitted or received.
Transmission is initiated by any instruction that writes to SBUF.
The data is shifted out of the RXD line. The eight bits are trans-
mitted with the least-significant bit (LSB) first, as shown in
Figure 39.
CORE
CLK
ALE
RXD
(DATA OUT)
TXD
(SHIFT CLOCK)
DATA BIT 0
DATA BIT 1
DATA BIT 6
DATA BIT 7
S6
S5
S4
S3
S2
S1
S6
S5
S4
S3
S2
S1
S6
S5
S4
S3
S2
S1
MACHINE
CYCLE 8
MACHINE
CYCLE 7
MACHINE
CYCLE 2
MACHINE
CYCLE 1
Figure 39. UART Serial Port Transmission, Mode 0
Reception is initiated when the receive enable bit (REN) is 1 and
the receive interrupt bit (RI) is 0. When RI is cleared the data is
clocked into the RXD line and the clock pulses are output from
the TXD line.
Mode 1: 8-Bit UART, Variable Baud Rate
Mode 1 is selected by clearing SM0 and setting SM1. Each data
byte (LSB first) is preceded by a start bit(0) and followed by a stop
bit(1). Therefore 10 bits are transmitted on TXD or received on
RXD. The baud rate is set by the Timer 1 or Timer 2 overflow
rate, or a combination of the two (one for transmission and the
other for reception).
Transmission is initiated by writing to SBUF. The “write to
SBUF” signal also loads a 1 (stop bit) into the ninth bit position
of the transmit shift register. The data is output bit by bit until
the stop bit appears on TXD and the transmit interrupt flag (TI)
is automatically set as shown in Figure 40.
TXD
TI
(SCON.1)
START
BIT
D0
D1
D2
D3
D4
D5
D6
D7
STOP BIT
SET INTERRUPT
i.e., READY FOR MORE DATA
Figure 40. UART Serial Port Transmission, Mode 0
Reception is initiated when a 1-to-0 transition is detected on
RXD. Assuming a valid start bit was detected, character reception
continues. The start bit is skipped and the eight data bits are
clocked into the serial port shift register. When all eight bits have
been clocked in, the following events occur:
The eight bits in the receive shift register are latched into SBUF
The ninth bit (Stop bit) is clocked into RB8 in SCON
The Receiver interrupt flag (RI) is set
if, and only if, the following conditions are met at the time the
final shift pulse is generated:
RI = 0, and
Either SM2 = 0, or SM2 = 1 and the received stop bit = 1.
If either of these conditions is not met, the received frame is
irretrievably lost, and RI is not set.
Mode 2: 9-Bit UART with Fixed Baud Rate
Mode 2 is selected by setting SM0 and clearing SM1. In this
mode the UART operates in 9-bit mode with a fixed baud rate.
The baud rate is fixed at Core_Clk/64 by default, although by
setting the SMOD bit in PCON, the frequency can be doubled to
Core_Clk/32. Eleven bits are transmitted or received, a start bit(0),
eight data bits, a programmable ninth bit and a stop bit(1). The
ninth bit is most often used as a parity bit, although it can be used
for anything, including a ninth data bit if required.
To transmit, the eight data bits must be written into SBUF. The
ninth bit must be written to TB8 in SCON. When transmission is
initiated the eight data bits (from SBUF) are loaded onto the
transmit shift register (LSB first). The contents of TB8 are loaded
into the ninth bit position of the transmit shift register. The trans-
mission will start at the next valid baud rate clock. The TI flag
is set as soon as the stop bit appears on TXD.
Reception for Mode 2 is similar to that of Mode 1. The eight
data bytes are input at RXD (LSB first) and loaded onto the
receive shift register. When all eight bits have been clocked in,
the following events occur:
The eight bits in the receive shift register are latched into SBUF
The ninth data bit is latched into RB8 in SCON
The Receiver interrupt flag (RI) is set
if, and only if, the following conditions are met at the time the
final shift pulse is generated:
RI = 0, and
Either SM2 = 0, or SM2 = 1 and the received stop bit = 1.
If either of these conditions is not met, the received frame is
irretrievably lost, and RI is not set.
Mode 3: 9-Bit UART with Variable Baud Rate
Mode 3 is selected by setting both SM0 and SM1. In this mode
the 8051 UART serial port operates in 9-bit mode with a variable
baud rate determined by either Timer 1 or Timer 2. The opera-
tion of the 9-bit UART is the same as for Mode 2 but the baud
rate can be varied as for Mode 1.
In all four modes, transmission is initiated by any instruction that
uses SBUF as a destination register. Reception is initiated in Mode 0
by the condition RI = 0 and REN = 1. Reception is initiated in
the other modes by the incoming start bit if REN = 1.
UART Serial Port Baud Rate Generation
Mode 0 Baud Rate Generation
The baud rate in Mode 0 is fixed:
Mode 0 Baud Rate = (Core Clock Frequency
1/12)
NOTE
1In these descriptions Core Clock Frequency refers to the core clock frequency
selected via the CD0–2 bits in the PLLCON SFR.
Mode 2 Baud Rate Generation
The baud rate in Mode 2 depends on the value of the SMOD bit
in the PCON SFR. If SMOD = 0, the baud rate is 1/64 of the core
clock. If SMOD = 1, the baud rate is 1/32 of the core clock:
Mode 2 Baud Rate = (2
SMOD/64)
× (Core Clock Frequency)
Modes 1 and 3 Baud Rate Generation
The baud rates in Modes 1 and 3 are determined by the overflow
rate in Timer 1 or Timer 2, or both (one for transmit and the
other for receive).
REV. A
相關PDF資料
PDF描述
VE-B32-IY-F2 CONVERTER MOD DC/DC 15V 50W
VE-B32-IY-F1 CONVERTER MOD DC/DC 15V 50W
VE-B32-CU-B1 CONVERTER MOD DC/DC 15V 200W
VE-B31-IY-F4 CONVERTER MOD DC/DC 12V 50W
3E106-1230 KV CONN PLUG IEEE 1394 VERTICAL
相關代理商/技術參數
參數描述
ADUC816BSZ-REEL 功能描述:IC MCU FLASH 16BIT ADC 52MQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND
ADUC824 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter, Dual-Channel 16-/24-Bit ADCs with Embedded FLASH MCU
ADUC824BCP 制造商:Analog Devices 功能描述:MCU 8-Bit ADuC8xx 8052 CISC 8KB Flash 3.3V/5V 56-Pin LFCSP EP 制造商:Rochester Electronics LLC 功能描述:8BIT CISC 8KB FLASH 12.58MHZ 3.3/5V 56LFCSP - Bulk
ADUC824BCP-REEL 制造商:Analog Devices 功能描述:MCU 8-Bit ADuC8xx 8052 CISC 8KB Flash 3.3V/5V 56-Pin LFCSP EP T/R
ADUC824BCPZ 功能描述:IC MCU 8K FLASH ADC/DAC 56LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*