- 您現在的位置：買賣IC網 > PDF目錄165354 > ADS8519IRHBR (TEXAS INSTRUMENTS INC) 3-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PQCC32 PDF資料下載
參數資料
| 型號： | ADS8519IRHBR |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | ADC |
| 英文描述： | 3-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PQCC32 |
| 封裝： | 5 X 5 MM, QFN-32 |
| 文件頁數： | 7/25頁 |
| 文件大?。?/td> | 396K |
| 代理商： | ADS8519IRHBR |
www.ti.com
PRODUCTPREVIEW
BASIC OPERATION
READING DATA
INTERNAL DATACLK
EXTERNAL DATACLK
SLAS462 – JUNE 2007
Two signals control conversion in the ADS8519: CS and R/C. These two signals are internally ORed together. To
start a conversion the chip must be selected, CS low, and the conversion signal must be active, R/C low. Either
signal can be brought low first. Conversion starts on the falling edge of the second signal. BUSY goes low when
conversion starts and returns high after the data from that conversion is shifted into the internal storage register.
Sampling begins when BUSY goes high.
To reduce the number of control pins CS can be tied low permanently. The R/C pin now controls conversion and
data reading exclusively. In the external clock mode this means that the ADS8519 will clock out data whenever
R/C is brought high and the external clock is active. In the internal clock mode data is clocked out every convert
cycle regardless of the states of CS and R/C. The ADS8519 provides a TAG input for cascading multiple
converters together.
The conversion result is available as soon as BUSY returns to high therefore, data always represents the
conversion previously completed even when it is read during a conversion. The ADS8519 outputs serial data in
either straight binary or binary two’s compliment format. The SB/BTC pin controls the format. Data is shifted out
MSB first. The first conversion immediately following a power-up will not produce a valid conversion result.
Data can be clocked out with either the internally generated clock or with an external clock. The EXT/INT pin
controls this function. If external clock is used the TAG input can be used to daisy-chain multiple ADS8519 data
pins together.
In the internal clock mode data for the previous conversion is clocked out during each conversion period. The
internal data clock is synchronized to the internal conversion clock so that is does not interfere with the
conversion process.
The DATACLK pin becomes an output when EXT/INT is low. 16 clock pulses are generated at the beginning of
each conversion after timing t8 is satisfied, i.e. you can only read previous conversion result during conversion.
DATACLK returns to low when it is inactive. The 16 bits of serial data are shifted out the DATA pin synchronous
to this clock with each bit available on a rising and then a falling edge. DATA pin returns to the state of TAG pin
input sensed at the start of transmission.
The external clock mode offers several ways to retrieve conversion results. However, since the external clock
cannot be synchronized to the internal conversion clock care must be taken to avoid corrupting the data.
When EXT/INT is set high, the R/C and CS signals control the read state. When the read state is initiated the
result from the previously completed conversion is shifted out the DATA pin synchronous to the external clock
that is connected to the DATACLK pin. Each bit is available on a falling and then a rising edge. The maximum
external clock speed of 28.5 MHz allows data shifted out quickly either at the beginning of conversion or the
beginning of sampling.
There are several modes of operation available when using an external clock. It is recommended that the
external clock run only while reading data. This is the discontinuous clock mode. Since the external clock is not
synchronized to the internal clock that controls conversion slight changes in the external clock can cause
conflicts that can corrupt the conversion process. Specifications with a continuously running external clock
cannot be guaranteed. It is especially important that the external clock does not run during the second half of the
conversion cycle (approximately the time period specified by td11, see timing table).
In the discontinuous clock mode data can be read during conversion or during sampling, with or without a SYNC
pulse. Data read during a conversion must meet the td11 timing specification. Data read during sampling must be
complete before starting a conversion.
Copyright 2007, Texas Instruments Incorporated
15
相關PDF資料 |
PDF描述 |
|---|---|
| ADSP-21060LCWZ-160 | 48-BIT, 40 MHz, OTHER DSP, CQFP240 |
| ADSP-TS101SKB2250X | 64-BIT, 125 MHz, OTHER DSP, PBGA484 |
| ADT70GR-REEL7 | ANALOG TEMP SENSOR-VOLTAGE, 2.49-2.51V, 1Cel, RECTANGULAR, SURFACE MOUNT |
| ADT7462ACPZ-500RL7 | DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), 4Cel, SQUARE, SURFACE MOUNT |
| ADTSM66SV | KEYPAD SWITCH, SPST, MOMENTARY-TACTILE, 0.05A, 12VDC, 3.92 N, SURFACE MOUNT-STRAIGHT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADS852 | 制造商:BB 制造商全稱:BB 功能描述:14-Bit, 65MHz Sampling ANALOG-TO-DIGITAL CONVERTER |
| ADS8528 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:12-, 14-, 16-Bit, Eight-Channel, Simultaneous Sampling ANALOG-TO-DIGITAL CONVERTERS |
| ADS8528SPM | 功能描述:模數轉換器 - ADC 12B,8Ch,Sim Sampling Bipolar Inp ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS8528SPMR | 功能描述:模數轉換器 - ADC 12B,8Ch,Sim Sampling Bipolar Inp ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS8528SRGCR | 功能描述:模數轉換器 - ADC 12B,8Ch,Bipolar Input ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。