- 您現在的位置：買賣IC網 > PDF目錄374016 > ADMCF340-EVALKIT (Analog Devices, Inc.) Circular Connector; No. of Contacts:7; Series:MS27497; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:10; Circular Contact Gender:Pin; Circular Shell Style:Wall Mount Receptacle; Insert Arrangement:10-99 RoHS Compliant: No PDF資料下載
參數資料
| 型號： | ADMCF340-EVALKIT |
| 廠商： | Analog Devices, Inc. |
| 元件分類： | 圓形連接器 |
| 英文描述： | Circular Connector; No. of Contacts:7; Series:MS27497; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:10; Circular Contact Gender:Pin; Circular Shell Style:Wall Mount Receptacle; Insert Arrangement:10-99 RoHS Compliant: No |
| 中文描述： | DashDSPTM 64無鉛閃存混合信號增強的DSP與模擬前端 |
| 文件頁數： | 25/40頁 |
| 文件大?。?/td> | 415K |
| 代理商： | ADMCF340-EVALKIT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
REV. 0
ADMCF340
–25–
The entire interrupt control system of the ADMCF340 is config-
ured and controlled by the IFC, IMASK, and ICNTL Registers of
the DSP core and the IRQFLAG Register for the PWMSYNC
and
PWMTRIP
interrupts and PORTA_FLAG Register for the
PIO interrupts.
Table X. Interrupt Vector Addresses
Interrupt Source
Interrupt Vector Address
PWMTRIP
Peripheral Interrupt (
IRQ2
)
PWMSYNC
PIO
Software Interrupt 1
Software Interrupt 0
SPORT0 Transmit Interrupt
SPORT0 Receive Interrupt
SPORT1 Transmit Interrupt (or
IRQ1)
0x0020
SPORT1 Receive Interrupt (or
IRQ0)
Timer
0x002C (Highest Priority)
0x0004
0x000C
0x0008
0x0018
0x001C
0x0010
0x0014
0x0024
0x0028 (Lowest Priority)
Interrupt Masking
Interrupt masking (or disabling) is controlled by the IMASK
Register of the DSP core. This register contains individual bits
that must be set to enable the various interrupt sources. If any
peripheral interrupt is to be enabled, the
IRQ2
interrupt enable
bit (Bit 9) of the IMASK Register must be set. The configura-
tion of the IMASK Register of the ADMCF340 is shown at the
end of the data sheet.
Interrupt Configuration
The IFC and ICNTL Registers of the DSP core control and
configure the interrupt controller of the DSP core. The IFC
Register is a 16-bit register that may be used to force and/or clear
any of the eight DSP interrupts. Bits 0 to 7 of the IFC Register
may be used to clear the DSP interrupts while Bits 8 to 15 can
be used to force a corresponding interrupt. Writing to Bits 11
and 12 in IFC is the only way to create the two software interrupts.
The ICNTL Register is used to configure the sensitivity (edge or
level) of the
IRQ0
,
IRQ1,
and
IRQ2
interrupts and to enable/
disable interrupt nesting. Setting Bit 0 of ICNTL configures the
IRQ0
as edge-sensitive, while clearing the bit configures it for
level-sensitive. Bit 1 is used to configure the
IRQ1
interrupt and
Bit 2 is used to configure the
IRQ2
interrupt. It is recommended
that the
IRQ2
interrupt always be configured for level-sensitive
as this ensures that no peripheral interrupts are lost. Setting Bit 4
of the ICNTL Register enables interrupt nesting. The configura-
tion of both IFC and ICNTL Registers is shown at the end of
the data sheet.
INTERRUPT OPERATION
Following a reset, the ROM code on the ADMCF340 must copy a
default interrupt vector table into program memory RAM from
address 0x0000 to 0x002F. Since each interrupt source has a
dedicated four word space in this vector table, it is possible to
code short interrupt service routines (ISR) in place. Alterna-
tively, it may be necessary to insert a JUMP instruction to the
appropriate start address of the interrupt service routine if more
memory is required for the ISR. When an interrupt occurs, the
program sequencer ensures that there is no latency (beyond
synchronization delay) when processing unmasked interrupts. In
the case of the Timer, SPORT0, SPORT1 and software interrupts,
the interrupt controller automatically jumps to the appropriate
location in the interrupt vector table. At this point, a JUMP
instruction to the appropriate ISR is required. Motor control
peripheral interrupts are slightly different. When a peripheral
interrupt is detected, a bit is set in the IRQFLAG Register for
PWMSYNC and
PWMTRIP
or in the PORTA_FLAG Register
for a PIO interrupt, and the
IRQ2
line is pulled low until all
pending interrupts are acknowledged. The DSP software must
determine the source of the interrupts by reading IRQFLAG
register. If more than one interrupt occurs simultaneously, the
higher priority interrupt service routine is executed. Reading the
IRQFLAG Register clears the
PWMTRIP
and PWMSYNC bits
and acknowledges the interrupt, thus allowing further interrupts
when the ISR exits. A user’s PIO interrupt service routine must
read the PORTA_FLAG Register to determine which PIO port
is the source of the interrupt. Reading register PORTA_FLAG
clears all bits in the registers and acknowledges the interrupt,
thus allowing further interrupts after the ISR exits. The configu-
ration of all these registers is shown at the end of the data sheet.
SYSTEM CONTROLLER
The system controller block of the ADMCF340 performs the
following functions:
1. Manages the interface and data transfer between the DSP
core and the motor control peripherals
2. Handles interrupts generated by the motor control peripherals
and generates a DSP core interrupt signal
IRQ2
3. Controls the ADC multiplexer select lines
4. Enables PWMTRIP and PWMSYNC interrupts
5. Controls the multiplexing of the SPORT1 and SPORT0 pins
6. Controls the PWM single/double update mode
7. Controls the ADC conversion time modes and the
SHA timers
8. Controls the auxiliary PWM operation mode
9. Contains a status register (SYSSTAT) that indicates the
state of the PWMTRIP Pin, the watchdog timer, and the
PWM timer
10. Performs a reset of the motor control peripherals and
control registers following a hardware, software, or watch-
dog initiated reset
SPORT1 and SPORT0 Control
The ADMCF340 has two serial ports: SPORT0 and SPORT1.
SPORT1 is available with a limited number of pins and is mainly
intended as a secondary port for Development Tools interfacing
and/or for Code Booting from an external serial memory.
Figure 18 shows the internal multiplexing of the SPORT0 and
SPORT1 signals. SPORT0 is intended as general-purpose
communication port. SPORT0 can support the following
operating modes: SPORT, UART, and SPI.
SPORT1 Configuration
There are two operating modes for SPORT1: Boot Mode and
UART Mode. These modes are selectable through Bit 4 of
MODECTRL Register. With SPORT1 in Boot Mode, SPORT1
serial clock (SCLK1) is externally available through the SCLK1/
SCLK0 pin. The signal SCLK1 is used to drive the external
serial memory input clock.
相關PDF資料 |
PDF描述 |
|---|---|
| ADMCF341 | DashDSP⑩ 28-Lead Flash Mixed-Signal DSP with Enhanced Analog Front End |
| ADMCF341BR | DashDSP⑩ 28-Lead Flash Mixed-Signal DSP with Enhanced Analog Front End |
| ADMCF341-EVALKIT | DashDSP⑩ 28-Lead Flash Mixed-Signal DSP with Enhanced Analog Front End |
| ADN2811 | OC-48/OC-48 FEC Clock and Data Recovery IC with Integrated Limiting Amp |
| ADN2811ACP-CML | OC-48/OC-48 FEC Clock and Data Recovery IC with Integrated Limiting Amp |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADMCF340XSTB | 制造商:Analog Devices 功能描述: |
| ADMCF341 | 制造商:AD 制造商全稱:Analog Devices 功能描述:DashDSP⑩ 28-Lead Flash Mixed-Signal DSP with Enhanced Analog Front End |
| ADMCF341BR | 制造商:Analog Devices 功能描述:DSP Fixed-Point/Floating-Point 16-Bit 20MHz 20MIPS 28-Pin SOIC W T/R |
| ADMCF341BRZ-REEL | 制造商:Analog Devices 功能描述: |
| ADMCF341-EVALKIT | 制造商:AD 制造商全稱:Analog Devices 功能描述:DashDSP⑩ 28-Lead Flash Mixed-Signal DSP with Enhanced Analog Front End |
發布緊急采購，3分鐘左右您將得到回復。