- 您現在的位置：買賣IC網 > PDF目錄16821 > AD9958/PCBZ (Analog Devices Inc)BOARD EVALUATION FOR AD9958 PDF資料下載
參數資料
| 型號： | AD9958/PCBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 11/44頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVALUATION FOR AD9958 |
| 產品培訓模塊： | Direct Digital Synthesis Tutorial Series (1 of 7): Introduction Direct Digital Synthesizer Tutorial Series (7 of 7): DDS in Action Direct Digital Synthesis Tutorial Series (3 of 7): Angle to Amplitude Converter Direct Digital Synthesis Tutorial Series (6 of 7): SINC Envelope Correction Direct Digital Synthesis Tutorial Series (4 of 7): Digital-to-Analog Converter Direct Digital Synthesis Tutorial Series (2 of 7): The Accumulator |
| 設計資源： | Low Jitter Sampling Clock Generator for High Performance ADCs Using AD9958/9858 and AD9515 (CN0109) Phase Coherent FSK Modulator (CN0186) AD9958/59 Eval Brd Schematics AD9958/59 Eval Brd Gerber Files AD9958 Eval Brd BOM |
| 標準包裝： | 1 |
| 系列： | AgileRF™ |
| 主要目的： | 計時，直接數字合成（DDS） |
| 嵌入式： | 否 |
| 已用 IC / 零件： | AD9958 |
| 主要屬性： | 10 位數模轉換器，32 位調節字寬 |
| 次要屬性： | 500MHz 2 通道圖形用戶界面 |
| 已供物品： | 板，線纜，軟件 |
| 產品目錄頁面： | 552 (CN2011-ZH PDF) |
| 相關產品： | AD9958BCPZ-REEL7-ND - IC DDS DUAL 10BIT DAC 56LFCSP AD9958BCPZ-ND - IC DDS DUAL 500MSPS DAC 56LFCSP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
Data Sheet
AD9958
Rev. B | Page 19 of 44
MODES OF OPERATION
There are many combinations of modes (for example, single-
tone, modulation, linear sweep) that the AD9958 can perform
simultaneously. However, some modes require multiple data
pins, which can impose limitations. The following guidelines
can help determine if a specific combination of modes can be
performed simultaneously by the AD9958.
CHANNEL CONSTRAINT GUIDELINES
Single-tone mode, two-level modulation mode, and linear
sweep mode can be enabled on either channel and in any
combination simultaneously.
Both channels can perform four-level modulation
simultaneously.
Either channel can perform eight-level or 16-level
modulation. The other channel can only be in single-tone
mode.
The RU/RD function can be used on both channels in
single-tone mode. See the Output Amplitude Control
Mode section for the RU/RD function.
When Profile Pin P2 and Profile Pin P3 are used for
RU/RD, either channel can perform two-level modulation
with RU/RD or both channels can perform linear
frequency or phase sweep with RU/RD.
When Profile Pin P3 is used for RU/RD, either channel can
be used in eight-level modulation with RU/RD. The other
channel can only be in single-tone mode.
When SDIO_1, SDIO_2, and SDIO_3 pins are used for
RU/RD, either or both channels can perform two-level
modulation with RU/RD. If one channel is not in two-level
modulation, it can only be in single-tone mode.
When the SDIO_1, SDIO_2, and SDIO_3 pins are used for
RU/RD, either or both channels can perform four-level
modulation with RU/RD. If one channel is not in four-level
modulation, it can only be in single-tone mode.
When the SDIO_1, SDIO_2, and SDIO_3 pins are used for
RU/RD, either channel can perform eight-level modulation
with RU/RD. The other channel can only be in single-tone
mode.
When the SDIO_1, SDIO_2, and SDIO_3 pins are used for
RU/RD, either channel can perform 16-level modulation with
RU/RD. The other channel can only be in single-tone mode.
Amplitude modulation, linear amplitude sweep modes,
and the RU/RD function cannot operate simultaneously,
but frequency and phase modulation can operate
simultaneously with the RU/RD function.
POWER SUPPLIES
The AVDD and DVDD supply pins provide power to the DDS
core and supporting analog circuitry. These pins connect to a
1.8 V nominal power supply.
The DVDD_I/O pin connects to a 3.3 V nominal power supply.
All digital inputs are 3.3 V logic except for the CLK_MODE_SEL
input. CLK_MODE_SEL (Pin 24) is an analog input and should
be operated by 1.8 V logic.
SINGLE-TONE MODE
Single-tone mode is the default mode of operation after a master
reset signal. In this mode, both DDS channels share a common
address location for the frequency tuning word (Register 0x04)
and phase offset word (Register 0x05). Channel enable bits are
provided in combination with these shared addresses. As a
result, the frequency tuning word and/or phase offset word can
be independently programmed between channels (see the follow-
ing Step 1 through Step 5). The channel enable bits do not
require an I/O update to enable or disable a channel.
See the Register Maps and Bit Descriptions section for a
description of the channel enable bits in the channel select
register (CSR, Register 0x00). The channel enable bits are
enabled or disabled immediately after the CSR data byte is
written.
Address sharing enables channels to be written simultaneously,
if desired. The default state enables all channel enable bits.
Therefore, the frequency tuning word and/or phase offset word
is common to all channels but written only once through the
serial I/O port.
The following steps present a basic protocol to program a
different frequency tuning word and/or phase offset word for
each channel using the channel enable bits.
1. Power up the DUT and issue a master reset. A master reset
places the part in single-tone mode and single-bit mode for
serial programming operations (refer to the Serial I/O Modes
of Operation section). Frequency tuning words and phase
offset words default to 0 at this point.
2. Enable only one channel enable bit (Register 0x00) and
disable the other channel enable bit.
3. Using the serial I/O port, program the desired frequency
tuning word (Register 0x04) and/or the phase offset word
(Register 0x05) for the enabled channel.
4. Repeat Step 2 and Step 3 for each channel.
5. Send an I/O update signal. After an I/O update, all
channels should output their programmed frequency
and/or phase offset values.
相關PDF資料 |
PDF描述 |
|---|---|
| AD9957/PCBZ | BOARD EVAL AD9957 QUADRATURE MOD |
| GCA22DRMD-S288 | CONN EDGECARD 44POS .125 EXTEND |
| AD9959/PCBZ | BOARD EVALUATION FOR AD9959 |
| ECM12DTKT-S288 | CONN EDGECARD 24POS .156 EXTEND |
| ATWEBDVK-02RC | KIT DEV TCP/IP AT89C51RD2 REMOTE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9959 | 制造商:AD 制造商全稱:Analog Devices 功能描述:4 Channel 500MSPS DDS with 10-bit DACs |
| AD9959/PCBZ | 功能描述:BOARD EVALUATION FOR AD9959 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PSoC® 主要目的:電源管理，熱管理 嵌入式:- 已用 IC / 零件:- 主要屬性:- 次要屬性:- 已供物品:板，CD，電源 |
| AD9959/PCBZ | 制造商:Analog Devices 功能描述:AD9959, DDS, DAC, GUI, USB, EVALUATION B |
| AD9959/PCBZ1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:4-Channel, 500 MSPS DDS with 10-Bit DACs |
| AD9959_08 | 制造商:AD 制造商全稱:Analog Devices 功能描述:4-Channel, 500 MSPS DDS with 10-Bit DACs |
發布緊急采購，3分鐘左右您將得到回復。