參數資料
型號： AD9951YSVZ
廠商： Analog Devices Inc
文件頁數： 7/28頁
文件大?。?/td> 0K
描述： IC DDS DAC 14BIT 1.8V 48-TQFP
產品培訓模塊： Direct Digital Synthesis Tutorial Series (1 of 7): Introduction
Direct Digital Synthesizer Tutorial Series (7 of 7): DDS in Action
Direct Digital Synthesis Tutorial Series (3 of 7): Angle to Amplitude Converter
Direct Digital Synthesis Tutorial Series (6 of 7): SINC Envelope Correction
Direct Digital Synthesis Tutorial Series (4 of 7): Digital-to-Analog Converter
Direct Digital Synthesis Tutorial Series (2 of 7): The Accumulator
標準包裝： 1
分辨率（位）： 14 b
主 fclk： 400MHz
調節字寬（位）： 32 b
電源電壓： 1.71 V ~ 1.96 V
工作溫度： -40°C ~ 105°C
安裝類型： 表面貼裝
封裝/外殼： 48-TQFP 裸露焊盤
供應商設備封裝： 48-TQFP 裸露焊盤（7x7）
包裝： 托盤
產品目錄頁面： 552 (CN2011-ZH PDF)
AD9951
Rev. A | Page 15 of 28
Control Register Bit Descriptions
Control Function Register No. 1 (CFR1)
The CFR1 is used to control the various functions, features,
and modes of the AD9951. The functionality of each bit is
detailed below.
CFR1<31:27>: Not Used
CFR1<26>: Amplitude Ramp Rate Load Control Bit
CFR1<26> = 0 (default). The amplitude ramp rate timer is
loaded only upon timeout (timer == 1) and is not loaded due to
an I/O UPDATE input signal.
CFR1<26> = 1. The amplitude ramp rate timer is loaded upon
timeout (timer == 1) or at the time of an I/O UPDATE input signal.
CFR1<25>: Shaped On-Off Keying Enable Bit
CFR1<25> = 0 (default). Shaped on-off keying is bypassed.
CFR1<25> = 1. Shaped on-off keying is enabled. When enabled,
CFR1<24> controls the mode of operation for this function.
CFR1<24>: Auto Shaped On-Off Keying Enable Bit (Only Valid
when CFR1<25> Is Active High)
CFR1<24> = 0 (default). When CFR1<25> is active, a Logic 0
on CFR1<24> enables the manual shaped on-off keying
operation. Each amplitude sample sent to the DAC is multiplied
by the amplitude scale factor. See the Shaped On-Off Keying
section for details.
CFR1<24> = 1. When CFR1<25> is active, a Logic 1 on
CFR1<24> enables the auto shaped on-off keying operation.
Toggling the OSK pin high will cause the output scalar to ramp
up from zero scale to the amplitude scale factor at a rate
determined by the amplitude ramp rate. Toggling the OSK pin
low will cause the output to ramp down from the amplitude
scale factor to zero scale at the amplitude ramp rate. See the
Shaped On-Off Keying section for details.
CFR1<23>: Automatic Synchronization Enable Bit
CFR1<23> = 0 (default). The automatic synchronization feature
of multiple AD9951s is inactive.
CFR1<23> = 1. The automatic synchronization feature of
multiple AD9951s is active. The device will synchronize its
internal synchronization clock (SYNC_CLK) to align to the
signal present on the SYNC_IN input. See the Synchronizing
Multiple AD9951s section for details.
CFR1<22>: Software Manual Synchronization of Multiple
AD9951
CFR1<22> = 0 (default). The manual synchronization feature is
inactive.
CFR1<22> = 1. The software controlled manual synchroniza-
tion feature is executed. The SYNC_CLK rising edge is
advanced by one SYNC_CLK cycle and this bit is cleared. To
advance the rising edge multiple times, this bit needs to be set
for each advance. See the Synchronizing Multiple AD9951s
section for details.
CFR1<21:14>: Not Used
CFR1<13>: Auto-Clear Phase Accumulator Bit
CFR1<13> = 0 (default), the current state of the phase
accumulator remains unchanged when the frequency tuning
word is applied.
CFR1<13> = 1. This bit automatically synchronously clears
(loads 0s into) the phase accumulator for one cycle upon
reception of an I/O UPDATE signal.
CFR1<12>: Sine/Cosine Select Bit
CFR1<12> = 0 (default). The angle-to-amplitude conversion
logic employs a COSINE function.
CFR1<12> = 1. The angle-to-amplitude conversion logic
employs a SINE function.
CFR1<11>: Not Used
CFR1<10>: Clear Phase Accumulator
CFR1<10> = 0 (default). The phase accumulator functions as
normal.
CFR1<10> = 1. The phase accumulator memory elements are
cleared and held clear until this bit is cleared.
CFR1<9>: SDIO Input Only
CFR1<9> = 0 (default). The SDIO pin has bidirectional
operation (2-wire serial programming mode).
CFR1<9> = 1. The serial data I/O pin (SDIO) is configured as
an input only pin (3-wire serial programming mode).
CFR1<8>: LSB First
CFR1<8> = 0 (default). MSB first format is active.
CFR1<8> = 1. The serial interface accepts serial data in LSB
first format.
CFR1<7>: Digital Power-Down Bit
CFR1<7> = 0 (default). All digital functions and clocks are active.
CFR1<7> = 1. All non-IO digital functionality is suspended,
lowering the power significantly.
相關PDF資料
PDF描述
AD9952YSVZ-REEL7 IC DDS DAC 14BIT 1.8V 48TQFP
AD9953YSVZ-REEL7 IC DDS DAC 14BIT 1.8V 48TQFP
AD9954YSVZ-REEL7 IC DDS DAC 14BIT 1.8V 48TQFP
AD9956YCPZ-REEL7 IC SYNTHESIZER 1.8V 48LFCSP
AD9957BSVZ-REEL IC DDS 1GSPS 14BIT IQ 100TQFP
相關代理商/技術參數
參數描述
AD9951YSVZ-REEL7 制造商:Analog Devices 功能描述:DGTL SYNTHESIZER 48TQFP EP TAPE AND REEL - Tape and Reel
AD9952 制造商:AD 制造商全稱:Analog Devices 功能描述:400 MSPS 14-Bit, 1.8 V CMOS Direct Digital Synthesizer
AD9952/PCB 制造商:Analog Devices 功能描述:Evaluation Board For Digital Synthesizer 制造商:Analog Devices 功能描述:400 MSPS 14BIT CMOS DIRECT DGTL SYNTHESIZER - Bulk 制造商:Rochester Electronics LLC 功能描述:- Bulk
AD9952YSV 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述:IC DDS 400MSPS SMD 9952 TQFP48
AD9952YSV-REEL7 制造商:AD 制造商全稱:Analog Devices 功能描述:400 MSPS 14-Bit, 1.8 V CMOS Direct Digital Synthesizer
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*