參數資料
型號： AD9923ABBCZ
廠商： ANALOG DEVICES INC
元件分類： 消費家電
英文描述： CCD Signal Processor with V-Driver and Precision Timing⑩ Generator
中文描述： SPECIALTY CONSUMER CIRCUIT, PBGA105
封裝： 8 X 8 MM, 0.65 MM PITCH, ROHS COMPLIANT, MO-225, CSPBGA-105
文件頁數： 61/88頁
文件大小： 852K
代理商： AD9923ABBCZ
AD9923A
STANDBY MODE OPERATION
The AD9923A contains three standby modes to optimize the
overall power dissipation in various applications. Bits[1:0] of
Register 0x00 control the power-down state of the device:
Rev. 0 | Page 61 of 88
STANDBY[1:0] = 00 = normal operation (full power)
STANDBY[1:0] = 01 = Standby 1 mode
STANDBY[1:0] = 2 = Standby 2 mode
STANDBY[1:0] = 3 = Standby 3 mode (lowest power)
Table 42 and Table 43 summarize the operation of each power-
down mode. Note that when OUTCONTROL = LO, it takes
priority over the Standby 1 and Standby 2 modes in determining
the digital output states, but Standby 3 mode takes priority over
OUTCONTROL. Standby 3 has the lowest power consumption,
and can shut down the crystal oscillator circuit between CLI
and CLO. If CLI and CLO are being used with a crystal to
generate the master clock, this circuit is powered down and
there is no clock signal. When returning the device from
Standby 3 mode to normal operation, reset the timing core at
least 500 μs after writing to the STANDBY register (Bits[1:0],
Address 0x00). This allows sufficient time for the crystal circuit
to settle. The vertical and shutter outputs can be programmed
to hold a specific value during the Standby 3 mode using
Register 0xE2, as detailed in Table 43. The vertical outputs can be
programmed to hold a specific value when OUTCONTROL =
low, or when in Standby 1 or Standby 2 mode, by using
Register 0xF3. The following list provides guidelines for the
mapping of the bits in these registers to the various vertical and
shutter outputs when the device is in one of the three standby
modes, or when OUTCONTROL = low.
Standby 3 mode takes priority over OUTCONTROL for
determining the output polarities.
These polarities assume OUTCONTROL = high, because
OUTCONTROL = low takes priority over Standby 1 and
Standby 2.
Standby 1 and Standby 2 set H and RG drive strength to
their minimum values (4.3 mA).
VD and HD default to High-Z status when in slave mode
regardless of standby mode or OUTCONTROL status.
This feature is useful during power-up if different polarities are
required by the V-driver and CCD to prevent damage.
It is important to note that when VDR_EN = 0 V, V1 to V13 are
at VM, and SUBCK is at VLL regardless of the state of the value
of the STANDBY and OUTCONTROL registers.
Table 42. Standby Mode Operation
I/O Block
AFE
Timing Core
CLO Oscillator
CLO
HL
H1
H2
H3
H4
RG
VD
5
HD
DCLK
D0 to D11
1
To exit Standby 3, write 00 to STANDBY (Bits[1:0], Address 0x00), then reset the timing core after 500 μs to guarantee proper settling of the oscillator.
2
Standby 3 mode takes priority over OUTCONTROL for determining the output polarities.
3
These polarities assume OUTCONTROL = high, because OUTCONTROL = low takes priority over Standby 1 and Standby 2.
4
Standby 1 and Standby 2 set H and RG drive strength to their minimum values (4.3 mA).
5
VD and HD default to High-Z status when in slave mode regardless of Standby mode or OUTCONTROL status.
Standby 3 (Default)
1
,
2
Off
Off
Off
High
High-Z
High-Z
High-Z
High-Z
High-Z
High-Z
Low
Low
Low
Low
OUTCONTROL = LOW
2
No change
No change
No change
Running
Low
Low
High
Low
High
Low
VDHDPOL value
VDHDPOL value
Running
Low
Standby 2
3
,
4
Off
Off
On
Running
Low (4.3 mA)
Low (4.3 mA)
High (4.3 mA)
Low (4.3 mA)
High (4.3 mA)
Low (4.3 mA)
VDHDPOL value
VDHDPOL value
Low
Low
Standby 1
3
,
4
Only REFT, REFB on
On
On
Running
Low (4.3 mA)
Low (4.3 mA)
High (4.3 mA)
Low (4.3 mA)
High (4.3 mA)
Low (4.3 mA)
Running
Running
Running
Low
相關PDF資料
PDF描述
AD9923ABBCZRL CCD Signal Processor with V-Driver and Precision Timing⑩ Generator
AD9925BBCZRL CCD Signal Processor with Vertical Driver and Precision Timing Generator
AD9925 CCD Signal Processor with Vertical Driver and Precision Timing Generator
AD9925BBCZ CCD Signal Processor with Vertical Driver and Precision Timing Generator
AD9927 14-Bit CCD Signal Processor with V-Driver and Precision TimingTM Generator
相關代理商/技術參數
參數描述
AD9923ABBCZRL 功能描述:IC PROCESSOR CCD 12BIT 105CSPBGA RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件
AD9923BBCZ 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Analog Devices 功能描述:
AD9923BBCZRL 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述:
AD9924BBCZ 制造商:Analog Devices 功能描述:
AD9924BBCZRL 制造商:Rochester Electronics LLC 功能描述:- Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*